Announcement

Collapse
No announcement yet.

The Official List-Your-Mods Thread

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Exterior:
    Repainted mirrors and valence
    Clear front indicator lenses
    Minty euro bumpers (replaced dented ones)

    Interior:
    Grey carpet swap
    Black Door Cards
    Black leather rear with headrests
    Reupholstered Sports fronts in black

    Suspension:
    JOM Coilovers

    Wheels/Tires:
    BBS RS003, Repolished and centres painted metallic grey
    Khumo Solus 205/55/16

    Brakes:
    New Front Pads
    New Front Rotors

    Drivetrain:
    b27/auto :(
    New Water pump timing belt


    Doesn't really look like much, but its alot better than when i bought it. MTech 1 kit and spare b2.7/731 head is in the garage waiting for funds tho!
    sigpic
    Delphin '87 325i Vert

    Comment


      Exterior:
      -Thule roof rack w/ 2 bike carriers
      -Ellipsoid headlight and yellow lamin-x on fogs
      -325i oil cooler duct
      -painted lower valance
      - 'i' lip
      -smoked tails
      -antenna delete plug
      -debadged
      -black kidneys
      -US plate filler

      Interior/ICE
      -E46 center console
      -Momo tuner steering wheel
      -Momo phantom shift knob
      -E34 ebrake handle w/ E46 leather boot
      -Sony headunit
      -Polk/Momo components front and rear
      -OBC blank panel
      -Amp rack in trunk
      -excess hardware/sound deadening/spare etc removed for weight

      Wheels/Suspension/brakes
      -TRM C1 15X8 wheels
      -OE rotors and some pads I forget
      -ATE blue fluid
      -Bilstien sport shocks
      -H&R sport springs (1 coil cut)
      -E90 drop hats
      -new end links
      -new tie rods

      Engine/Drivetrain
      -M42
      -TMS chip
      -K&N filter
      -mess under the intake delete
      -P/S delete
      -A/C delete
      -Washer tank delete
      -starting mild bay shaving
      -new valve cover, oil filter housing, oil pan, intake manifold, TB gaskets. All painted aswell
      -high flow cat, resonator delete, superturbo muffler
      -new thermostat, housing and gasket
      -Bav auto coil packs
      -UUC SSK
      -new axles
      -new clutch (already slipping! :hitler:)

      Weighed in at 2480lbs with 1/2 tank of gas. Shooting for low 2400 or into the 2300's.





      91 318is M50 swapped
      05 Honda Pilot

      24V swap thread
      http://www.r3vlimited.com/board/showthread.php?t=302524

      Comment


        Exterior:
        -Alpine white
        -BMP design front bumper
        -Late model Ellipsoid
        -plasti dipped rear bumper
        -debadged
        -Euro Grilles
        -black kidneys
        -Euro plate filler for early model
        -Shadowline trim

        Interior
        -Alpine headunit
        -JL audio rear speakers
        -White cluster
        -2000watt amp
        -Kicker classic 12" sub
        -Black doorcards
        -Black rear seat
        -Black sportseats
        -custom rear deck port in to trunk

        Wheels/Suspension/
        -BBS RS 17"x8 with a stepped lip
        -kumo 205x40?x17
        -Raceland Coilovers with rear perches out


        Engine/Drivetrain
        -M20
        -getrag 260
        -Dinan chip
        -K&N filter
        -A/C delete
        -Washer fluid delete
        -2.75 strightpipe

        Working On Swap
        -Shaved bay
        -s50
        -ZF Trans
        -e34 oilpan
        -e34 dipstick and dipstick tube
        -A/C delete
        -e34 throttle cable
        -Solid engine mounts
        -F1 lightweight clutch and flywheel
        -318is radiator
        -coolant overflow tank delete
        -ABS Delete
        -M3 DriveLine
        -Chipped ECU
        All i can remember right now, swap will be in be late December.
        My e30:
        Click image for larger version

Name:	IMG_2345.jpg
Views:	1
Size:	82.9 KB
ID:	7161469
        My s50 (before i took off the A/C compressor):
        Click image for larger version

Name:	IMG_2242.jpg
Views:	1
Size:	61.2 KB
ID:	7161468
        - S50 Swapped E30 1/1 Mineral White -
        @vaughnbannister on IG

        Comment


          318is 80k miles, bought it torn apart as a racecar that was owned by Aaron Reid, the brother of Jason Reid who did the body work for 1552 when they were in Florida. He had a kid and sold it to a neighbor who let it sit until I got it. It was abandoned in the beginning of the build. It's almost finished now, but that will be another thread.

          H&R springs and shocks, lowered about 2.5" front and 3" rear via trimmed top coil.
          M3 offset CABs
          E36 m3 steering rack
          Xxr531 15x8 et20 with Falken 195/50

          Downing-Atlanta Z3 supercharger
          Bosch Volvo 740 turbo 32# injectors
          NGK bkr7e plugs
          Tweaked cam timing
          Cone filter because air box won't fit anymore
          Innovate LC-1
          14point7 UAFC
          E36 318 serpentine/v-belt combo conversion
          Some strange muffler that sounds great

          Dodge Sublime green base/clear
          Custom hand painted mini truck flames on hood
          Graffiti side mirrors
          Depo smoked smileys
          Ddm tuning 5500k HIDs
          Debadged and shaved emblems

          3 spoke sport wheel
          Tan and black 2 tone swap
          Real leather 325 seat swap
          Dynamatted floors, firewall, doors, sunroof, and trunk
          No ICE at all yet
          Crack free dash (original!)

          Next mods:
          Full serpentine swap
          Power steering belt back on
          Electric fan swap
          Audio setup
          Skid plate
          Rear bushing refresh
          Full 2.75 exhaust
          E90 hats
          Short shifter
          225/50 all around and 10mm spacers on the rear

          Someday:
          Ac repair and r134a conversion
          3.73 LSD
          ms3 or vems and dyno tuning
          Smaller pulley
          MAP conversion
          Cams
          Thicker head gasket
          sigpic

          Comment


            1992 325i Cabriolet, Schwartz

            Exterior:
            Hard top
            homemade poplar roof-rack
            iX flares and skirts
            16" Voxx wheels

            Under the hood:
            2.5l M20B25

            Sooooo fricking close:
            M90 Thinderbird Supercoupe supercharger
            custom aluminum air intake
            MS2
            Originally posted by Andy.B
            Whenever I am about to make a particularly questionable decision regarding a worryingly cheap diy solution, I just ask myself, "What would Ether-D do?"
            1987 325iS m30b34 Muscle car (Engine electrical phase)
            ~~~~~~~~~~
            I was born on 3/25…
            ~~~~~~~~~~

            Comment


              Exterior:
              early model is air dam
              Hella fog lights (soon to be moved to my truck)
              Garage Line duck bill spoiler (in the mail)
              tucked bumpers of cores
              US ellipsoids smoked with cross hairs
              Z3 stubby antenna
              Hella dual tone horns

              Interior:
              Stripped
              Group A style half cage with integrated rear strut tower bar and battery box
              MOMO XL Super Cup seat (driver)
              Planted side mounts
              e21 sport seat (passenger) until I buy another bucket seat
              Gforce 5 point harnesses
              MOMO Monte Carlo wheel
              Sparco quick release
              Steering column spacer aka chunk of square tubing
              Fire extinguisher
              dual USB port for iPhone and GoPro
              Chariot Gauge + iPhone

              Wheels/Tires:
              TRM 15x8
              Dunlop Direzza ZII
              Motorsport Hardware 75mm bullet nose black

              Suspension:
              Catuned coil over kit
              IE 25mm sway bar kit
              Welded reinforcements
              Condor bushings
              IE rear camber/toe tabs

              Drive line/Steering:
              Z3 1.9 rack w/ condor PS delete
              Condor drive line bushings
              373 LSD

              Engine:
              Bone stock but very strong m20b25
              SSSquid 24pin 89 octane chip
              Drive way welded/geto fab, stock diameter pipe, Magnaflow glass pack center, Magnaflow muffler
              sigpic
              "The bitterness of poor quality remains long after the sweetness of low price is forgotten."

              Comment


                my 16 year olds,..father/son project e30

                * the basis of this build is an early production (1985) pre-facelift BMW e30, 325e.




                1....... E30 325e

                * 2 door coupe, color is zinnabar rot, interior is tan leather sport package with momo steering wheel and hub adapter.
                * factory early e30 "is" front spoiler
                * factory e28 "is" rear spoiler

                2....... Transmission is Getrag model 260

                * overdrive 5 speed backed with a rebuilt 3.25 limited slip , medium case ( 188mm) differential.
                *rebuilt large flange driveshaft
                *owner fabricated DTM style chassis mounted shift assembly, all bushings or pivot points are delrin.


                3....... Engine

                engine is based on an m20b27 overhead cam inline six.
                *compression ratio is 9.5 to 1,
                *cylinder head is a european market 731 casting .
                *this head is unique as it matches the dome profile of the m20b27 pistons.
                *head has been pressure checked, surface cut for straightness, 3 angle valve job, new bronze valve guides, new seals, *new oem double valve springs, 1mm larger intake and exhaust valves, 270 degree cam installed with no advance or retard.
                *head has had intake ports matched to m20b25 "i" intake manifold.
                * m20b25 "i" throttle body
                engine management is bosch motronic version 1.0 with upgraded chip. stage 1 chip currently installed with more aggressive timing and fuel maps, rev limit is currently 5200rpm.
                *SSQUID Tuning chip being burnt to complement engine mods and to allow 6800 rpm redline . Custom SSQUID chip will be installed after sufficient break in time and installation of numerical higher geared differential ( 3.46 or 3.73) stage 2 chip will have a more aggressive tune and will subsequently raise rev limit to 6800 rpm.
                # exhaust currently uses factory cast iron manifolds, oem catalytic converter backed with custom fabricated 2.5 inch exhaust with both resonator and rear muffler.
                * flywheel is a single mass unit that has been lightened to 12#s, factory is 22#s, cutch, pressure plate thow out bearing and clutch hydraulics are all new .

                4........Suspension

                * IP brand 60/40mm lowering springs, German market TUV approved
                * KYB gas charged strut inserts and rear shocks
                * Ireland Engineering front adjustable camber plates
                * Ireland Engineering 25mm front, 19mm rear adjustable sway bars. all polyurethane bushings.
                *Ireland Engineering billet rear swaybar mounts with chassis tie ins, rear sway bar mount gusseting, rear sway bar adjustable heim joint linkage
                * Ireland Engineering front subframe reinforcement plates , Ireland Engineering adjustable heim joint linkage
                * new lower control arms with e36 M3 offset control arm bushings
                * new front and rear rotors, brake pads
                * all factory rubber spring isolation pads removed
                * currently set with approximately 2.0 degrees negative front camber for aggressive turn in


                5.......Wheels/tires


                * 16x8.5 et 25mm BBS RS replica wheels with 4x100mm bolt pattern
                * studs replace lug bolts as fasteners
                * 20mm rear, 10mm front hubcentric spacers
                * 205/50x16 tires with 260 treadwear rating


                6.......Audio

                * Kenwood 4 channel head unit with usb and aux inputs
                * all speaker wiring is dedicated, and does not use factory chassis ground wiring
                * Monoblock dedicated single channel subwoofer amplifier with remote gain control
                * factory premium rear speakers using Boston Acoustics crossovers
                * 5 1/4 dual cone front speakers
                * 10" subwoofer in ported enclosure firing through factory ski pass, unit is solidly mounted to rear trunk wall
                * Passport radar detector


                as purchased ( $100 bucks :)





                as it currently sits.....lotsa 16 year olds blood sweat, busted knuckles and dads checkbook..


                Comment


                  Originally posted by canyoncarver View Post
                  * the basis of this build is an early production (1985) pre-facelift BMW e30, 325e.




                  1....... E30 325e

                  * 2 door coupe, color is zinnabar rot, interior is tan leather sport package with momo steering wheel and hub adapter.
                  * factory early e30 "is" front spoiler
                  * factory e28 "is" rear spoiler

                  2....... Transmission is Getrag model 260

                  * overdrive 5 speed backed with a rebuilt 3.25 limited slip , medium case ( 188mm) differential.
                  *rebuilt large flange driveshaft
                  *owner fabricated DTM style chassis mounted shift assembly, all bushings or pivot points are delrin.


                  3....... Engine

                  engine is based on an m20b27 overhead cam inline six.
                  *compression ratio is 9.5 to 1,
                  *cylinder head is a european market 731 casting .
                  *this head is unique as it matches the dome profile of the m20b27 pistons.
                  *head has been pressure checked, surface cut for straightness, 3 angle valve job, new bronze valve guides, new seals, *new oem double valve springs, 1mm larger intake and exhaust valves, 270 degree cam installed with no advance or retard.
                  *head has had intake ports matched to m20b25 "i" intake manifold.
                  * m20b25 "i" throttle body
                  engine management is bosch motronic version 1.0 with upgraded chip. stage 1 chip currently installed with more aggressive timing and fuel maps, rev limit is currently 5200rpm.
                  *SSQUID Tuning chip being burnt to complement engine mods and to allow 6800 rpm redline . Custom SSQUID chip will be installed after sufficient break in time and installation of numerical higher geared differential ( 3.46 or 3.73) stage 2 chip will have a more aggressive tune and will subsequently raise rev limit to 6800 rpm.
                  # exhaust currently uses factory cast iron manifolds, oem catalytic converter backed with custom fabricated 2.5 inch exhaust with both resonator and rear muffler.
                  * flywheel is a single mass unit that has been lightened to 12#s, factory is 22#s, cutch, pressure plate thow out bearing and clutch hydraulics are all new .

                  4........Suspension

                  * IP brand 60/40mm lowering springs, German market TUV approved
                  * KYB gas charged strut inserts and rear shocks
                  * Ireland Engineering front adjustable camber plates
                  * Ireland Engineering 25mm front, 19mm rear adjustable sway bars. all polyurethane bushings.
                  *Ireland Engineering billet rear swaybar mounts with chassis tie ins, rear sway bar mount gusseting, rear sway bar adjustable heim joint linkage
                  * Ireland Engineering front subframe reinforcement plates , Ireland Engineering adjustable heim joint linkage
                  * new lower control arms with e36 M3 offset control arm bushings
                  * new front and rear rotors, brake pads
                  * all factory rubber spring isolation pads removed
                  * currently set with approximately 2.0 degrees negative front camber for aggressive turn in


                  5.......Wheels/tires


                  * 16x8.5 et 25mm BBS RS replica wheels with 4x100mm bolt pattern
                  * studs replace lug bolts as fasteners
                  * 20mm rear, 10mm front hubcentric spacers
                  * 205/50x16 tires with 260 treadwear rating


                  6.......Audio

                  * Kenwood 4 channel head unit with usb and aux inputs
                  * all speaker wiring is dedicated, and does not use factory chassis ground wiring
                  * Monoblock dedicated single channel subwoofer amplifier with remote gain control
                  * factory premium rear speakers using Boston Acoustics crossovers
                  * 5 1/4 dual cone front speakers
                  * 10" subwoofer in ported enclosure firing through factory ski pass, unit is solidly mounted to rear trunk wall
                  * Passport radar detector


                  as purchased ( $100 bucks :)





                  as it currently sits.....lotsa 16 year olds blood sweat, busted knuckles and dads checkbook..


                  Thats an E28 Mtech 1 spoiler, not an iS. The car looks great though.
                  Originally posted by flyboyx
                  how about if i yank the anal beads out of your ass like i'm trying to pull start a chain saw?
                  Originally posted by Northern
                  beer is my new liver cleanse.

                  Henna - '84 Hennarot 325e
                  Lola - '89 Schwarz 325is - being saved
                  Christine - '88 Schwarz 325is - Spec E30 Racecar
                  '01 White F150 Lariat 4x4 Supercrew - Daily
                  Dad's '05 Interlagosblau M3

                  Comment


                    87' 325is

                    Exterior:
                    Delphin Metallic
                    early "is" airdam
                    Morimoto mini h1
                    4300k HID
                    35w ballast

                    Interior:
                    Houndstooth sport interior
                    Houndstooth doorcards
                    Ninestitch leather w/ mstitching shift/parking brake boots
                    z3m shift rod
                    zhp weighted knob
                    Cubby hole gauges
                    Airvent mounted Wideband gauge


                    Suspension:
                    BC br Coilovers
                    ST 22mm/19mm sway bars
                    IE reinforced Sway bar mounts
                    IE adjustable sway bar links
                    Full condor bushings

                    Wheels/Tires:
                    15x7 BBS RZ
                    205/50 Yokahama s.drive

                    Brakes:
                    Brembo blanks
                    Hawk HPS Pads

                    Drivetrain:
                    m30b35
                    g260
                    '86 Delphin 335i turbo -
                    '88 Schwarz 325i -
                    '94 w124 e420 -
                    Turbo m30b35 Build Thread

                    Comment


                      Originally posted by PimpinWalrus View Post
                      87' 325is

                      Exterior:
                      Delphin Metallic
                      early "is" airdam
                      Morimoto mini h1
                      4300k HID
                      35w ballast

                      Interior:
                      Houndstooth sport interior
                      Houndstooth doorcards
                      Ninestitch leather w/ mstitching shift/parking brake boots
                      z3m shift rod
                      zhp weighted knob
                      Cubby hole gauges
                      Airvent mounted Wideband gauge


                      Suspension:
                      BC br Coilovers
                      ST 22mm/19mm sway bars
                      IE reinforced Sway bar mounts
                      IE adjustable sway bar links
                      Full condor bushings

                      Wheels/Tires:
                      15x7 BBS RZ
                      205/50 Yokahama s.drive

                      Brakes:
                      Brembo blanks
                      Hawk HPS Pads

                      Drivetrain:
                      m30b35
                      g260

                      Pics?
                      Originally posted by flyboyx
                      how about if i yank the anal beads out of your ass like i'm trying to pull start a chain saw?
                      Originally posted by Northern
                      beer is my new liver cleanse.

                      Henna - '84 Hennarot 325e
                      Lola - '89 Schwarz 325is - being saved
                      Christine - '88 Schwarz 325is - Spec E30 Racecar
                      '01 White F150 Lariat 4x4 Supercrew - Daily
                      Dad's '05 Interlagosblau M3

                      Comment


                        Originally posted by HennaE30 View Post
                        Pics?
                        Only pic i have with the front end together



                        Check out my build thread for some better pics
                        '86 Delphin 335i turbo -
                        '88 Schwarz 325i -
                        '94 w124 e420 -
                        Turbo m30b35 Build Thread

                        Comment


                          '85 318

                          Body:
                          Steel flares
                          Steel front damn/rear skit thingies
                          Smoothed side mouldings
                          Shortened & smoothed euro bumpers, full width rear, 1/4 fronts
                          Sunroof delete
                          E46 rear floor
                          Shaved and relocated fuel filler
                          Drop tank

                          Interior:
                          Super basic black
                          Retrimmed shit spec std seats.
                          No rear seat.

                          Wheels/Tires:
                          Black BBS RK 17x8 et35
                          Some Dunlop 235/40s

                          Suspension:
                          E46 front
                          E46 rear
                          Bilstein PSS9
                          328 E46 front & rear brakes with ABS & std pads.

                          Steering:
                          328 E46 rack and column.
                          Some random Sportline wheel.

                          Electrics:
                          2000 E46 loom & modules.

                          Engine/gearbox/diff:
                          Stock M62B44
                          Factory DME with manual software/coding.
                          Factory early 265mm E39 clutch and dualmass flywheel
                          Getrag 420
                          E46 med case 2.98 diff.
                          Dual 2 1/2" into 3" into E39 res into Remus rear box

                          Some other stuff I forget....
                          sigpic

                          Comment


                            I don't recall ever doing this......

                            1991 325i Sport; deck spoiler, side skirts, LSD, sport seats, etc. all orig. equipment.


                            Uni air filter
                            Fabbed alum AFM mount unknown origin
                            IE plug wires
                            17# greentop injectors
                            AC/PS delete (including pulleys)
                            Hartge muffler
                            Mizu oversize aluminum radiator
                            Early 323i light flywheel
                            Garagistic delrin shift bushings

                            Koni yellows
                            mystery lowering springs
                            E90 drop hats
                            Euro manual steering rack
                            Offset LCA bushes
                            325ic 21mm front swaybar
                            M3/ix 14mm rear swaybar
                            AKG rear subframe bushes
                            AKG rear control arm bushes
                            Garagistic rear camber/toe kits
                            IE swaybar brackets w/ poly bushes
                            Fabbed swaybar tab reinforcements
                            Stoptech braided steel brake lines
                            Generic long wheel studs/nuts
                            3mm front spacers
                            Alpina 15x7 et12 wheels
                            Hankook Ventus2 205/50R15

                            Early schwartz vinyl interior swap (from natur leather)
                            Sport steering wheel/airbag delete
                            Euro fuel and economy gauges
                            Euro clock
                            Manual window conversion
                            Momo shift knob
                            E34 leather parking brake handle
                            Bav Auto fitted floor mats (fucking suck)

                            Euro corner moldings/side marker delete
                            Euro plate filler
                            US Elipsoid headlights
                            Rolled fenders


                            Daily driven!




                            sigpic
                            1991 325i Sport - Calypsorot Metallic - DAILY DRIVEN

                            WTB in SoCal: 8"/10" Lukebox, leather Sport steering wheel, 60L MotoMeter fuel gauge, Thule/Yakima roof rack

                            Comment


                              1989 325i 4door

                              Exterior:
                              Sunroof delete
                              Single wiper conversion
                              Polycarbonate side windows
                              Fiberglass hood
                              ABS mirrors
                              Side molding delete

                              Interior:
                              Gutted
                              Caged
                              Corbeau FIA seat
                              Momo Mod 30
                              NRG Short hub/quick release
                              Wink mirror

                              Go:
                              S50B30US
                              All new sensors/seals
                              21.5lb injectors
                              AC delete
                              PS Delete
                              New timing guides
                              Achilles oil pump
                              Ishihara-Johnson crank scraper
                              VAC baffle
                              KAMotors air intake
                              Mishimoto radiator
                              SPAL 16
                              AKG solid mounts
                              Ebay headers, custom y-pipe
                              3" no cat into Magnaflow straight through
                              ZF310
                              UUC 8.5lb flywheel
                              E34 M5 Clutch
                              AKG StageII shifter with DTM selector rod
                              Revshift swap guibo
                              Condor mounts
                              3.25 lsd
                              New half shafts

                              Stop:
                              ABS delete
                              Massive booster delete
                              25mm E32 Master
                              All new nickle copper lines
                              Stainless hoses
                              Motul 600
                              New calipers
                              Brass bushings
                              UUC rotors
                              Hawk pads

                              Steering/suspension:
                              E36 rack
                              Reinforced/powdercoated subframe
                              New OE tie rods
                              New Lemforder control arms
                              AKG Lower control arm brackets
                              H&R Super Sports
                              Bilstein Sports
                              AKG Aluminum spherical bearing rear shock mounts
                              Rear shock mount reinforcements
                              IE adjustable sway bars
                              Garagistic front sway links with strut tube mount
                              Ground control Spec E30 adjustable camber plates
                              Motorsport hardware studs/nuts
                              Motorsport Hardware 12mm Traklite spacers
                              TRMotorsports C1
                              BFG Rival S 225/45 15

                              Not daily driven but technically still street legal.

                              Click image for larger version

Name:	IMG_3966.jpg
Views:	1
Size:	97.1 KB
ID:	7181500
                              sigpic
                              89 4door S50 - The White Dog
                              87 325i Vert
                              Custom T-Shirts and More
                              Check us out at ColorCreek.com

                              Comment




                                Started life as a humble 320i auto, right down to the 14 inch steel wheels with plastic hub caps!

                                Asides from my RG Alpina reps, the car is total sleeper on the outside (or OEM+), but with a lot more grunt!

                                Mods (usual M30 swap stuff)

                                Engine
                                M30B35 engine
                                e30.de Mounts
                                Miller MAF
                                exhaust manifold mods to clear RHD
                                Many e28, e34 and e32 bits to make it all work in the e30 chassis as a factory one would.
                                hi flow cat
                                2.5 inch single exhaust

                                Driveline
                                Auto to manual swap (G240)
                                Australian Clutch Service XTreme HD clutch kit
                                3.25 LSD (e28)

                                Suspension / Wheels / Brakes
                                16 x 7 RG Alpina Reps
                                Eibach Pro Kit springs
                                Bilstein sport shocks
                                urethane offset Cabs, rear subframe and swing arm bushes
                                Noltech camber and caster adjustable strut tops
                                m-tech front sway bar from iS

                                Interior
                                80s era Recaro LX-B
                                M-tech 2 steering wheel and shift knob
                                Nakamichi CD head unit

                                Misc
                                Factory tow kit (it has a tractor engine, why not use the torque :) )
                                Last edited by lukeADE335i; 01-07-2019, 02:39 PM.
                                My e30: OEM+ with M30B35

                                Comment

                                Working...
                                X