6 sets in stock.
Announcement
Collapse
No announcement yet.
E30 OEM Hella European Clear Ellipsoids (with Smilies and City Lights) $699 Set
Collapse
X
-
E30 OEM Hella European Clear Ellipsoids (with Smilies and City Lights) $699 Set
Mel Abrahams
Abrahams Motorsport
www.abrahamsmotorsport.com
E-mail:sales@abrahamsmotorsport.com
PayPal to:
order@abrahamsmotorsport.com
If you do not have a PayPal account, please call our office.
Buy with confidence, serving the E30 community for over 14 years
Phone:727-992-0288
Fax:727-868-6373Tags: None
-
They are new and have new adjusters.
H1 bulbs , City Light bulbs or connectors are not included.
The H1 and City Light bulbs are inexpensive from any auto parts store.
The Euro Ellipsoids need (four) H1 bulbs, the city light bulbs, the low beam & city light wiring. Before installing the Euro Ellipsoids, you will need to order a few other parts from the dealer to make this happen. The Euro Ellipsoids come with the high and low beam caps that seal off the rear of the lens. You will need the necessary wiring & plugs to power them up. You will need to order four (white) connector plugs & eight “circular wiring connectors” (wiring that fits into the white high beam plugs) that feed power to the high beams. Use some 18 gauge (stranded) wire from Radio Shack. You will need about 4 feet of the wire to tap into your side marker lights to power the city lights. Use tap splices for that. Use heat shrink tubing over the connections for added safety. The low beam & city lights are wired together (from the factory) into a sealed beam style plug. You will need to cut the four wires at the base of that plug connector- (Again, this is on a car that has stock US Ellipsoids- hence different plug connectors)
This is what is required :
Circular wiring connectors (x4) (Green wire sections about 12 inches long) 61130007445
White connector plugs (x2) 61131378417
Remove the city light harness from the low beam assembly (it just twists out). Cut about a foot of the 18 gauge wire to “extend” the city light harness (four 1 ft. sections will be needed). This is needed to tap into the side marker. Use the red colored butt connectors & heat shrink tubing over that.
Take out the stock US headlight assembly & pop out your side marker. Lace the city light harness through-down to the side marker & use two tap splices.
Cut off your stock Ellipsoid plug connectors (do one plug at a time). When connecting up to the new Euro plug, pull the socket off the back of the light assembly & follow through the brown colored ground wire. Keep the ground (BROWN) wire matched up to the BROWN stock wire off the factory harness on the car. Same goes for each of the positive wires as well. Again, use the red butt connectors & heat shrink tube over those as well. Pick up some “Spiral Wrap” from Wallmart to protect the wiring of each harness. It comes in 6 foot lengths and sells for under $2.
Some additional parts you may need:
61131378418 Grey Connector
61131378419 Yellow Connector
61130007446 Pigtails
Originally posted by _kanon View PostDo these come with the necessary pig tails and brand new adjusters?Mel Abrahams
Abrahams Motorsport
www.abrahamsmotorsport.com
E-mail:sales@abrahamsmotorsport.com
PayPal to:
order@abrahamsmotorsport.com
If you do not have a PayPal account, please call our office.
Buy with confidence, serving the E30 community for over 14 years
Phone:727-992-0288
Fax:727-868-6373
Comment
-
Originally posted by BMWE34M5 View PostThey are new and have new adjusters.
H1 bulbs , City Light bulbs or connectors are not included.
The H1 and City Light bulbs are inexpensive from any auto parts store.
The Euro Ellipsoids need (four) H1 bulbs, the city light bulbs, the low beam & city light wiring. Before installing the Euro Ellipsoids, you will need to order a few other parts from the dealer to make this happen. The Euro Ellipsoids come with the high and low beam caps that seal off the rear of the lens. You will need the necessary wiring & plugs to power them up. You will need to order four (white) connector plugs & eight “circular wiring connectors” (wiring that fits into the white high beam plugs) that feed power to the high beams. Use some 18 gauge (stranded) wire from Radio Shack. You will need about 4 feet of the wire to tap into your side marker lights to power the city lights. Use tap splices for that. Use heat shrink tubing over the connections for added safety. The low beam & city lights are wired together (from the factory) into a sealed beam style plug. You will need to cut the four wires at the base of that plug connector- (Again, this is on a car that has stock US Ellipsoids- hence different plug connectors)
This is what is required :
Circular wiring connectors (x4) (Green wire sections about 12 inches long) 61130007445
White connector plugs (x2) 61131378417
Remove the city light harness from the low beam assembly (it just twists out). Cut about a foot of the 18 gauge wire to “extend” the city light harness (four 1 ft. sections will be needed). This is needed to tap into the side marker. Use the red colored butt connectors & heat shrink tubing over that.
Take out the stock US headlight assembly & pop out your side marker. Lace the city light harness through-down to the side marker & use two tap splices.
Cut off your stock Ellipsoid plug connectors (do one plug at a time). When connecting up to the new Euro plug, pull the socket off the back of the light assembly & follow through the brown colored ground wire. Keep the ground (BROWN) wire matched up to the BROWN stock wire off the factory harness on the car. Same goes for each of the positive wires as well. Again, use the red butt connectors & heat shrink tube over those as well. Pick up some “Spiral Wrap” from Wallmart to protect the wiring of each harness. It comes in 6 foot lengths and sells for under $2.
Some additional parts you may need:
61131378418 Grey Connector
61131378419 Yellow Connector
61130007446 Pigtails
Comment
Comment