Laser cut Gauge panels NEW SELECTION!!

Screaming_bmwe30 · 04-18-2007, 10:44 PM

PM me for payment options/question

These are laser cut acrylic gauge panels precisely cut to the opening of the OBC location, CD player slot, Center vent location, drivers side vent, and Ash tray location on the e30 interiors. Most panels are so accurately cut that they nearly snap fit into the location with only a little bit of superglue to affix them permanently.

The CD player insert is fairly universal, and I am using one in my turbo e36 currently.

Garanteed to fit: if you are unhappy with your panel, I will give you a full refund, not including the cost to send it back.

different gauge sizes available in most pod designs.

1.5" / 38mm- for most mini gauges, like the sunpro mini series found at local autopart stores.

2" / 50mm- for some autometer gauges like the ultralight series etc.

2-1/16" / 55mm- Most sunpro, VDO and many autometer gauges are this size (most common gauge size)

2-5/8" / 66mm- Standard size for plus size gauges offered by autometer and others.

MEASURING YOUR GAUGE:

If you have a caliper, measure the diameter of the gauge closest to the bezel.

If you don't have a caliper, wrap a strand of string around gauge, and take that measurement, and do the following math:

(Measurement of string) divided by 3.14= Gauge Diameter

On Board Computer replacement: 13$ shipped

-Sizes and styles shown below.

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Center Vent panel 16$ shipped

-Center vent panel can accomodate any gauge size from 2-1/16" and smaller and up to 4 gauges can be accomodated.

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------

CD player insert panel: 15$ shipped

-Fits snugly in all e30 and even e36 CD player slots, and can be a permanent install with a few little dabs of super glue. Can accomodate 2-1/16" gauges and smaller in a variety of layouts.

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Ashtray insert: 14$ shipped

-The ashtray unit must be modified to accept gauges. If you send me your ash tray, I can do this modification for 10$ extra, which covers my time and $ to ship it back with the panel already installed.

-Comes in a variety of layouts in gauge sizes 2-1/16" and smaller. Can accomodate three 1.5" gauges. Great place to house switches, and blank customizable panels are available.

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Driver's side Vent panel: 8$ shipped

- Available in 2-1/16" Now!!

e30sd · 04-18-2007, 10:55 PM

those are pretty sweet for the price. free bump.

MR 325 · 04-18-2007, 11:05 PM

I have one of the OBC replacement panels. Top notch product here guys, and a good seller.

Jesse30 · 04-18-2007, 11:13 PM

hmm i may be interested in the drivers side and center vent..

i'll let you know.

Screaming_bmwe30 · 04-19-2007, 11:20 AM

will have pictures of actual panels updated tonight, stay tuned.

Screaming_bmwe30 · 04-25-2007, 03:06 PM

Updated pictures of CD panel, OBC, Center Vent, and Driver side vent panels.

T3rd Ferguson · 04-25-2007, 07:17 PM

how does on go about installing the OBC gauge panel? I'll take one, sending a PM.

Screaming_bmwe30 · 04-29-2007, 11:49 AM

OBC panel is easy. Remove the obc by unplugging it from the back, and popping it out. To get to the back of the OBC, simply open the glovebox, remove the plastic panel on the left leading to the backside of the OBC, and you should have plenty of room to remove it.

ALL panels ordered before 4/28 have been shipped

Majikal · 04-29-2007, 06:29 PM

Installed my OBC panel today, sorry for the crappy camera phone pic.

CleanAzzE30z · 04-29-2007, 08:08 PM

Had I seen this before I bought my waffleswaffleswaffleswafflesing gauge pod..... shit.

Mariano

JJe30 · 04-29-2007, 08:12 PM

Those are pretty sweet.

2002maniac · 04-30-2007, 03:56 PM

Quote:

Originally Posted by MR 325

I have one of the OBC replacement panels. Top notch product here guys, and a good seller.

ditto. great stuff. mine fit perfectly with no glue.

Screaming_bmwe30 · 05-02-2007, 10:46 AM

Thanks for the positive posts. I have all models ready for shipment. All orders made before 4/30 have been shipped.

ZM Blue Devil · 05-02-2007, 11:18 AM

Quote:

Originally Posted by CleanAzzE30z

Had I seen this before I bought my waffleswaffleswaffleswafflesing gauge pod..... shit.

Mariano

I may be interested, are you willing to sell?

CleanAzzE30z · 05-02-2007, 11:50 AM

Nah sorry, I already have it all wired up.

Mariano

04-18-2007, 10:44 PM	#1
Screaming_bmwe30 Advanced Member Join Date: Oct 2003 Location: Cincinnati, Ohio Posts: 128	Laser Cut Gauge Panels NEW STYLES as of 2/11/08 PM me for payment options/question These are laser cut acrylic gauge panels precisely cut to the opening of the OBC location, CD player slot, Center vent location, drivers side vent, and Ash tray location on the e30 interiors. Most panels are so accurately cut that they nearly snap fit into the location with only a little bit of superglue to affix them permanently. The CD player insert is fairly universal, and I am using one in my turbo e36 currently. Garanteed to fit: if you are unhappy with your panel, I will give you a full refund, not including the cost to send it back. different gauge sizes available in most pod designs. 1.5" / 38mm- for most mini gauges, like the sunpro mini series found at local autopart stores. 2" / 50mm- for some autometer gauges like the ultralight series etc. 2-1/16" / 55mm- Most sunpro, VDO and many autometer gauges are this size (most common gauge size) 2-5/8" / 66mm- Standard size for plus size gauges offered by autometer and others. MEASURING YOUR GAUGE: If you have a caliper, measure the diameter of the gauge closest to the bezel. If you don't have a caliper, wrap a strand of string around gauge, and take that measurement, and do the following math: (Measurement of string) divided by 3.14= Gauge Diameter On Board Computer replacement: 13$ shipped -Sizes and styles shown below. -------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Center Vent panel 16$ shipped -Center vent panel can accomodate any gauge size from 2-1/16" and smaller and up to 4 gauges can be accomodated. -------------------------------------------------------------------------------------------------------------------------------------------------------------------------- CD player insert panel: 15$ shipped -Fits snugly in all e30 and even e36 CD player slots, and can be a permanent install with a few little dabs of super glue. Can accomodate 2-1/16" gauges and smaller in a variety of layouts. -------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Ashtray insert: 14$ shipped -The ashtray unit must be modified to accept gauges. If you send me your ash tray, I can do this modification for 10$ extra, which covers my time and $ to ship it back with the panel already installed. -Comes in a variety of layouts in gauge sizes 2-1/16" and smaller. Can accomodate three 1.5" gauges. Great place to house switches, and blank customizable panels are available. -------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Driver's side Vent panel: 8$ shipped - Available in 2-1/16" Now!! __________________ Last edited by Screaming_bmwe30; 02-11-2008 at 01:08 PM..

04-18-2007, 10:55 PM	#2
e30sd Fistee Join Date: Jan 2004 Location: kazakhstan Posts: 5,431	those are pretty sweet for the price. free bump. __________________

04-18-2007, 11:05 PM	#3
MR 325 Moderator Join Date: Oct 2003 Location: La Crescenta, CA Posts: 31,462 Images: 1024	I have one of the OBC replacement panels. Top notch product here guys, and a good seller. __________________ 1991 E30 M-Technic 327i Turbo --- 1986 E30 325iS --- 1997 E36 M3/4/5 Ported, Polished, & Rebuilt M20 Cylinder Heads CLICK HERE! Castro Motorsport 12600 Sherman Way, North Hollywood 818.765.3606 - Ask for Chris

04-19-2007, 11:20 AM	#5
Screaming_bmwe30 Advanced Member Join Date: Oct 2003 Location: Cincinnati, Ohio Posts: 128	will have pictures of actual panels updated tonight, stay tuned. __________________

04-25-2007, 07:17 PM	#7
T3rd Ferguson No R3VLimiter Join Date: Aug 2005 Location: Killadelphia, PA Posts: 3,090 Images: 27	how does on go about installing the OBC gauge panel? I'll take one, sending a PM. __________________ 1989 Bronzit 325ia- Sold 1986 Diamondschwarz Grey Market 325i Sport Mtech 1- Parted out 1988 Delphin 327i- Sold 1995 Cosmos M3- Current

04-18-2007, 11:13 PM	#4
Jesse30 No R3VLimiter Join Date: Jan 2007 Location: Covina, California Posts: 3,914 Images: 1	hmm i may be interested in the drivers side and center vent.. i'll let you know.

04-25-2007, 03:06 PM	#6
Screaming_bmwe30 Advanced Member Join Date: Oct 2003 Location: Cincinnati, Ohio Posts: 128	Updated pictures of CD panel, OBC, Center Vent, and Driver side vent panels.

04-29-2007, 11:49 AM	#8
Screaming_bmwe30 Advanced Member Join Date: Oct 2003 Location: Cincinnati, Ohio Posts: 128	OBC panel is easy. Remove the obc by unplugging it from the back, and popping it out. To get to the back of the OBC, simply open the glovebox, remove the plastic panel on the left leading to the backside of the OBC, and you should have plenty of room to remove it. ALL panels ordered before 4/28 have been shipped __________________

04-29-2007, 06:29 PM	#9
Majikal E30 Addict Join Date: Nov 2006 Location: Hartford, CT Posts: 521	Installed my OBC panel today, sorry for the crappy camera phone pic. __________________

04-29-2007, 08:08 PM	#10
CleanAzzE30z R3V OG Join Date: Jan 2004 Location: City of Angels, Killer Cali. Posts: 11,880 Images: 821	Had I seen this before I bought my waffleswaffleswaffleswafflesing gauge pod..... shit. Mariano __________________ 2001 Titaniumsilber 540i Sport 6-Speed 1990 Diamantschwarz Alpha-N 2.5L ///M3 1986 Alpinweiss 325e M50B25 (R.I.P.) -Talk to me when more sound comes from the induction than from the exhaust... -Argentina........lo mas grande que hay.

04-29-2007, 08:12 PM	#11
JJe30 E30 Mastermind Join Date: May 2006 Location: Vancouver, Wa. Posts: 1,895	Those are pretty sweet.

05-02-2007, 10:46 AM	#13
Screaming_bmwe30 Advanced Member Join Date: Oct 2003 Location: Cincinnati, Ohio Posts: 128	Thanks for the positive posts. I have all models ready for shipment. All orders made before 4/30 have been shipped. __________________

05-02-2007, 11:50 AM	#15
CleanAzzE30z R3V OG Join Date: Jan 2004 Location: City of Angels, Killer Cali. Posts: 11,880 Images: 821	Nah sorry, I already have it all wired up. Mariano __________________ 2001 Titaniumsilber 540i Sport 6-Speed 1990 Diamantschwarz Alpha-N 2.5L ///M3 1986 Alpinweiss 325e M50B25 (R.I.P.) -Talk to me when more sound comes from the induction than from the exhaust... -Argentina........lo mas grande que hay.