[ETA - E30 Adapters] 5 Lug kit with e46m3 front and e46 325/328i brake setup

[ngampleh]

Im in the initial stages of my swap and i have full e36m3 front end for this but the rears im still sorting but i have e36m3 (99) rear rotors and calipers, will your bracket work for these with the z4 flanges? Thanks just piecing it all together right now. and if the brackets work, prices on what i need to complete the 5 lug swap ie the brackets and anything else you would think i need?

No, the rear bracket wont fit for e36m3 rear brake setup on z4 flange

Sent from my SM-A310F using Tapatalk

[LowR3V'in]

still order these?

just some simple questions sorry if it's been clear before.

the bolt is to replace the washer that is folded over the hub nut?

the 325/328 is the only rear brake that allows the stock ebrake? Do u sell adapters for m3 rears if doing hydraulic?

i need 12mm spacer on all 4?
i like that. you can dial in some extra wheel space

[bornagain]

Im in the initial stages of my swap and i have full e36m3 front end for this but the rears im still sorting but i have e36m3 (99) rear rotors and calipers, will your bracket work for these with the z4 flanges? Thanks just piecing it all together right now. and if the brackets work, prices on what i need to complete the 5 lug swap ie the brackets and anything else you would think i need?

[ngampleh]

Hi, ready to order if you can answer these questions,

So with a 325/328i rotor the e30 handbrake will work without modification?

Do you still have those photos of the 3 brake hose options for the rear? They've been taken down because of photobucket

Why do you have to tap that left hand thread and put the locking bolt in instead of just using an OEM nut for the hub which you crimp into the axle when tight?

Thanks
Michael

Yes, It will work perfectly without any modification from stock e30 handbrake..

Here the options:




The custom new nut sit too far from the axle shaft,
and if its use crimp part.. will need to buy or made new custom nut again for future bearing replacement..

Sorry for late reply, my tapatalk didnt gave me any notif, lol...

[mikethebike]

Hi, ready to order if you can answer these questions,

So with a 325/328i rotor the e30 handbrake will work without modification?

Do you still have those photos of the 3 brake hose options for the rear? They've been taken down because of photobucket

Why do you have to tap that left hand thread and put the locking bolt in instead of just using an OEM nut for the hub which you crimp into the axle when tight?

Thanks
Michael

[ngampleh]

Bump a bit :)

Sent from my SM-A310F using Tapatalk

[ngampleh]

>>> 1st batch order <<<

1. Pancho22 ---> shipped
2. plnnsmpl ---> shipped
3. Yellow13 ---> shipped
4. Jack.sims29 (UK)---> shipped
5. Mera (Belgium) ---> shipped
6. Austin (US) ---> shipped
7.
8.
9.
10.

[ngampleh]

Sorry, one important point I forgot to mention was that I am planning to use e46 328i rear disc and caliper as this has the matching inner dimensions for e30 handbrake mechanism. I'm also upgrading to a mk60 abs system so will use a complete e46 328i front/rear setup with the same master cylinder to ensure proper balance of the system.

https://www.bremboparts.com/europe/en/catalogue/bmw-3-coupe-e46-328-ci/000010503-1

160.9mm this allows use of a 294mm vented rear disc on an e30.

Can you confirm if the brackets will work in this instance or if you can make brackets that will work.

Thank you

Yes, I confirm it... as long as you using z4 hubs...
I have sold this rear brackets worldwide for years...

Sent from my SM-A310F using Tapatalk

[Supafly]

Yes, I can sell only rear brackets

Rear spacers use to make same wider track with front, not for caliper

Yes, it will fit on e38 style5 16s...
Even 15s, it will fit too

Sorry, one important point I forgot to mention was that I am planning to use e46 328i rear disc and caliper as this has the matching inner dimensions for e30 handbrake mechanism. I'm also upgrading to a mk60 abs system so will use a complete e46 328i front/rear setup with the same master cylinder to ensure proper balance of the system.

https://www.bremboparts.com/europe/en/catalogue/bmw-3-coupe-e46-328-ci/000010503-1

160.9mm this allows use of a 294mm vented rear disc on an e30.

Can you confirm if the brackets will work in this instance or if you can make brackets that will work.

Thank you

[ngampleh]

Mera (Belgium) installed on his M50NV turbo

[ngampleh]

Yellow13 installed on his S54 car

e46m3 front



e46 330i rear

[ngampleh]

pics upload repaired...

[ngampleh]

Hi,

Will you sell a set of the rear brackets separately as I already have the fronts sorted?

Is the 20mm spacer on the rear to clear the caliper?

If I use the z4 rear hubs will e38 style 5 16x8 fit on the rear of my facelift e30 using these rear brakets?

Thanks

Yes, I can sell only rear brackets

Rear spacers use to make same wider track with front, not for caliper

Yes, it will fit on e38 style5 16s...
Even 15s, it will fit too

[Supafly]

Style 5 rear fitment

Hi,

Will you sell a set of the rear brackets separately as I already have the fronts sorted?

Is the 20mm spacer on the rear to clear the caliper?

If I use the z4 rear hubs will e38 style 5 16x8 fit on the rear of my facelift e30 using these rear brakets?

Thanks

[ngampleh]

>>> 1st batch order <<<

1. Pancho22 ---> shipped
2. plnnsmpl ---> shipped
3. Yellow13 ---> shipped
4. Jack.sims29 (UK)---> shipped
5. Mera (Belgium) ---> shipped
6.
7.
8.
9.
10.