E30 Smiley Euro Smoked Cross hair & Chrome Projector Headlights!

[jaywood]

the terminals on the HID harness should be flat male disconnects like these:




I don't think I have those connectors....



These are the female disconnect terminals from a sealed beam plug that was disassembled. There is no need to disassemble, just plug the male from the HID harness into the proper slot instead of wire-nut-capping the third one like this guy did.


this might help someone: http://www.billswebspace.com/E30Ligh...mationXMon.pdf

[bwawuz02]

the terminals on the HID harness should be flat male disconnects like these:


These are the female disconnect terminals from a sealed beam plug that was disassembled. There is no need to disassemble, just plug the male from the HID harness into the proper slot instead of wire-nut-capping the third one like this guy did.


this might help someone: http://www.billswebspace.com/E30Ligh...mationXMon.pdf

[jaywood]

5. plug male ends from HID harness into existing sealed beam socket (i'll go look and see which is pwr, gnd is brown on both sides)

Need help on this...

How do I get the original headlight plug (plugs into the back of a sealed beam, 3 prongs) to plug into the ballast?

I'm going from sealed beams to the DDM kit with these headlights.

[bwawuz02]

When did you order the bulbs/when did they come?

can't remember exactly, but I know it didn't take more than a week or so to get them. when i ordered my ST sways from them however, HOLY SHIT almost a month

thanks. christ those are on their solid, my roommate walked by when I was grunting from the strain and was like WTF dude

LMFAO!

so anyone with sealed beams installed these yet. Would love a DIY writeup to know how to go about this.

1. remove the 3 mounting screws holding the sealed beam assembly to the body
2. unplug sealed beams and throw in trash
3. mount new smoked smiley DEPO awesomeness where sealed beams once lived using same screws you removed
4. buy DDM HIDs before removing sealed beams (w/o 9005/6 adapters)
5. plug male ends from HID harness into existing sealed beam socket (i'll go look and see which is pwr, gnd is brown on both sides)
6. turn on awesome new lights

If you live in NorCal i'll do the whole install for $50. I even have some nice double side tape to secure the HID ballasts ;)

you do need a dremel to modify the caps to accept the HIDs, but every shadetree should invest in one of these anyhow.

[Trptguy]

so anyone with sealed beams installed these yet. Would love a DIY writeup to know how to go about this.

[straight6pwr]

Same thing happened to me....

Twist it a little harder. It'll come off

thanks. christ those are on their solid, my roommate walked by when I was grunting from the strain and was like WTF dude

[jaywood]

got mine in the mail today, the glass is so pretty! anyways, how do the rear caps come off these? i tried twisting/pulling but didnt want to pull to hard and break something.

Same thing happened to me....


Twist it a little harder. It'll come off

[sergio318is]

got mine in mail today also will take pics tommorrow

Sent from my PC36100 using Tapatalk

[Rsully70sev]

They twist, I promise you. You won't break anything.

[straight6pwr]

got mine in the mail today, the glass is so pretty! anyways, how do the rear caps come off these? i tried twisting/pulling but didnt want to pull to hard and break something.

[jaywood]

Got mine put in with DDM HIDs, very happy with them.

When did you order the bulbs/when did they come?

[bwawuz02]

Got mine put in with DDM HIDs, very happy with them.

[widebodye30]

MUST HAVE ON ANY E30!

[sergio318is]

looks very nice

Sent from my PC36100 using Tapatalk

[jaywood]