New girl on the forum and...

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • Mr.SWISS
    replied
    This is so hot.

    Leave a comment:


  • JayyE30
    replied
    ATTN:

    So Kingston suggest a great idea that I should continue on this thread on to the project forum since this IS the location strictly for questions and help (and not my updates and ramblings :( ) I will stop posting updates on here, instead I will post it on the new thread linked below. So if any of you are still interested and still want to support me

    here's the new thread :)


    THANK YOU !
    Sincerely,
    -Jaylissa.

    Leave a comment:


  • jrdeamicis
    replied
    When you go to put the S52 back in, use a load balancer and these mounting points.

    Rear - Small metal bracket above the starter has a M10x1.5 Bolt hole in it. Thread a bolt through it then a washer and the chain.

    Front - Bracket above the vanos.

    Life will be much better. Also you can drop in your motor fully loaded minus intake (you can do it with the intake also) But without the intake you can hook up all the heater hoses that are underneath the intake way easier. And OBD1 is super easy to install.

    Leave a comment:


  • kingston
    replied
    Originally posted by JayyE30
    This is really helpful thank you !
    For diff I was just thinking if the stock is alright?
    Ac is already out of the car, it feels like an oven in there. . .
    -Jaylissa

    What diff is in your car already?
    I currently have no A/C, but you can bet I will be installing A/C with the M50!

    Might want to start a dedicated build thread, instead of continuing this intro thread.

    I'm jealous of your engine hoist! Mine looks like it was salvaged from a German U-boat that had been underwater for 70 years! Ah, well, it works anyway... :)
    Last edited by kingston; 08-05-2011, 06:25 AM. Reason: spelling

    Leave a comment:


  • IminDiegoTriick
    replied
    I like :)

    I haven't even done a swap yet. So you haz more man points than me

    Leave a comment:


  • accident
    replied
    What a guy, that Danny.

    Leave a comment:


  • Justin B
    replied
    Good luck!

    Leave a comment:


  • Danny
    replied
    Yeah alright I'll help you with the swap.

    Leave a comment:


  • JayyE30
    replied
    Originally posted by reelizmpro
    This is cool. Good to see you are tackling this project head-on and not afraid to get dirty. Props to you. Can't wait to see the finished product.
    I been a grease monkey from working on cars , so I think Im pretty ready. I 'm just extremely excited and thank you for the support. I'll update everything just incase anyone 's interested on the swap . Keep checking back, I'll be here !
    -Jaylissa

    Leave a comment:


  • JayyE30
    replied
    Originally posted by phreshkid
    There is my buddy Danny that you bought the motor from
    Out of sac and then there is r3v's playboy "Danny" who likes long walks on the beach and jazz music.

    But seriously, you took my motor. I don't know if I could ever forgive you.
    Haha Im sorry, I m sure he's going to have more for you!
    -Jaylissa

    Leave a comment:


  • JayyE30
    replied
    Originally posted by kingston
    OK, sounds like you've got a pretty good head start on some of this. Here's some further thoughts...

    - For brake booster I haven't got one yet , which one would you recommend?I m looking at e21
    I went with the Zionsville Motorsports pre-modded E21 booster.

    - Im looking at a 3.5 MAF with 4" intake and SAMCO SPORT Siilicone elbow
    Eh, I probably wouldn't spend the dosh on the MAF. As far as the SAMCO elbow, I'd look around at a local speed shop. Probably get one for a lot less $$.

    - Motor mount:e28 Transmission mount:e21
    Some people on the board have reported problems with the E28 motor mounts. I personally am going with the mounts from Revshift. They are made specifically for the M/Sxx swaps. I have not seen anyone report any issues with them, and they're only about $40 more than E28 ones.

    - Just the gasket for the oil pan because of switching e34 oil pan oil pick up
    and dipstick
    Not replacing anything else? Water pump & gaskets, throttle body gaskets, injector o-rings, etc? Never a better time than when the engine's already out of the car...

    - For now I don't have the funds for the brake, but I'd like a full m3 brake .
    Going 5-lug, then? You'll need to if you want to use the M3 brakes.

    Are you going to keep A/C?
    What Diff are you going to use?
    Not sure on the ZF trans how the shifter carrier works on E30s.

    Keep us posted!
    This is really helpful thank you !
    For diff I was just thinking if the stock is alright?
    Ac is already out of the car, it feels like an oven in there. . .
    -Jaylissa

    Leave a comment:


  • phreshkid
    replied
    Originally posted by bernzpeed
    get over it. first come, first serve.
    It's alright I bought something with more litres.

    Leave a comment:


  • bernzpeed
    replied
    Originally posted by phreshkid
    There is my buddy Danny that you bought the motor from
    Out of sac and then there is r3v's playboy "Danny" who likes long walks on the beach and jazz music.

    But seriously, you took my motor. I don't know if I could ever forgive you.
    get over it. first come, first serve.

    Leave a comment:


  • ethrtyiS
    replied
    very cool. glad to see a girl tackling a a swap, especially s52.

    :)

    Leave a comment:


  • phreshkid
    replied
    There is my buddy Danny that you bought the motor from
    Out of sac and then there is r3v's playboy "Danny" who likes long walks on the beach and jazz music.

    But seriously, you took my motor. I don't know if I could ever forgive you.

    Leave a comment:

Working...