Swap 1/4 Mile Thread

[e30polak]

0-60mph in 5.96 secs, not 60ft
Using a 3.25LSD from an E28 and E36M3 ZF tranny

I took off at 3,000 rpm, and a little tire spin when shifted to 2nd

0-60 in practically 6 secs is horrible, stock e36 m3 runs it in like 5.6....haven't ran my swap at the track yet but i know it should be round 4.8-4.9

[EtaSport]

I may be headed to the dyno soon. And I do want to take mine to the strip sometime after I get the m20 flywheel in and fix the exhaust.

I used to run a 3.25 lsd with the getrag 260 trans and it was hard to catch on the highway. I had the advantage of shifting to 3rd even at 90. I was able to stay even with a e36m3 with that diff. Now i've got a 3.73 and the car feels more alive. It ran about even with a new Si that went 14.7s.

Ive got 93 m50tu, jim c chip, ebay headers, g260, s50 clutch, 3.73 gears.

[BingM3]

does it give you a trap speed?

So far, last 2 runs were somewhere between 96-98 mph

[gazellebeigem3]

does it give you a trap speed?

[BingM3]

Tried G-Tech again last night...0-60 in 5.77 secs with 1/4 of 14.10:)

[BingM3]

ahhh, not bad. what was your 0-60ft?

I'll see if it is still in the memory...

[325Projectz]

ahhh, not bad. what was your 0-60ft?

[BingM3]

holy 0-60ft time batman! 5.96?!?

traction issues is an understatement.

what is your driveline setup?

0-60mph in 5.96 secs, not 60ft
Using a 3.25LSD from an E28 and E36M3 ZF tranny

I took off at 3,000 rpm, and a little tire spin when shifted to 2nd

[325Projectz]

holy 0-60ft time batman! 5.96?!?

traction issues is an understatement.

what is your driveline setup?

[BingM3]

Just to add, I have raced an E46M3 on a highway, can keep up but no pass him, basically you won't get embarrassed. Last one I tried to hang with would not look at me when traffic got to a stop:)

[BingM3]

Recent G-Tech Pro Run bone stock S50 Motor

0-60 with 17's DSM's Wheels
5.96

1/4
14.46 secs

Traction issues, slipped a bit on 2nd

[BUDNUNTA]

True, that's why I chose the non vanos so I can easily get the AA s/c when time and funds allow. I also don't think any of these M50's run have been modded. I put the M3 peformance clutch and 11lb single mass fly over the 40lb dual mass on it and it revs really quick. Night and day over the old M20 I had. I think after I put the Schrick 252 on the intake and move my intake cam over to the exhaust side I will get another 20-30 more with the Turner chip. After that I plan on under drives and a better CAI that is blocked off from the rad. I think my 0-60 is around 6 now. I hope to have it down to 5 when done.

OT: got those headlights in yet?:D

Which chip are you going to be running?

[japspecvr6]

give me 3 weeks imma post my slips.........

[Mr.SWISS]

I can understand what you guys are saying. I'm just looking for something kinda quick for not so much $$ I guess. I suppose I could always boost it later though...

True, that's why I chose the non vanos so I can easily get the AA s/c when time and funds allow. I also don't think any of these M50's run have been modded. I put the M3 peformance clutch and 11lb single mass fly over the 40lb dual mass on it and it revs really quick. Night and day over the old M20 I had. I think after I put the Schrick 252 on the intake and move my intake cam over to the exhaust side I will get another 20-30 more with the Turner chip. After that I plan on under drives and a better CAI that is blocked off from the rad. I think my 0-60 is around 6 now. I hope to have it down to 5 when done.

OT: got those headlights in yet?:D

[DREWHALL]

I can understand what you guys are saying. I'm just looking for something kinda quick for not so much $$ I guess. I suppose I could always boost it later though...