A couple s50 swap questions

[dillon7]

Same car here. I ended up using the e34 m50 spider hose which connects from the back of the thermostat housing, to the lower radiator hookup you posted above, the throttle body and back to the heater core.

From what I read, you can't use the M20 hose if you are running an M42 rad. Hope that helps.

Helps a ton, thanks!

Damn son, clean that mess up under there haha! yeah get an M50 spider hose.

Edit: And don't forget your engine mount arm ground right there on the drivers side mount arm.

I'm just trying to get the damn thing running, then I'll make it pretty ;)

Thanks for the heads up on the ground, I haven't been too thorough with those

[NickL]

Damn son, clean that mess up under there haha! yeah get an M50 spider hose.

Edit: And don't forget your engine mount arm ground right there on the drivers side mount arm.

[BoxDriver86]

Same car here. I ended up using the e34 m50 spider hose which connects from the back of the thermostat housing, to the lower radiator hookup you posted above, the throttle body and back to the heater core.

From what I read, you can't use the M20 hose if you are running an M42 rad. Hope that helps.

[dillon7]

I have the long hose going to behind thermostat housing.

Looking at the pics I feel like I need to just get an m50 spider hose.

[NickL]

You must have something hooked up wrong then. On an M50 spider hose, there is two hoses that branch off the spider hose. One goes up to the expansion tank (the port you're wondering about) and the other is a smaller one to the throttle body.

M20 hose looks like it has one, aka the one that goes to the expansion tank. So I'm not sure where you have that going.

[justin_l_]

It may be possible, but I have never seen it done/done it. Going off memory here, the spider hose should connect from the back of the water pump, the coolant expansion tank (may need to get a longer peice of hose to reach m42 radiator), throttle body and heater core.

[dillon7]

Take a pic with your intake manifold off. There is an obd1 spider hose and a obd2 coolant pipe. You should have an obd1 spider hose. A pic will help us better.

I was told I could use the spider hose from my m20, is that wrong? It all hooks up.

[justin_l_]

Take a pic with your intake manifold off. There is an obd1 spider hose and a obd2 coolant pipe. You should have an obd1 spider hose. A pic will help us better.

[dillon7]

OK update.

I have almost everything hooked up and figured out. I had to take of the intake manifold so I could get a better view of everything.

That said, I still have to to find where the radiator hose can go. I have everything connected but that and there is no where for it to go. No where on the spider hose is open.

I know the spider hose differs from year to year but since mine has no opening I have no idea what to do. Buy another spider hose? Or plug the radiator?

[dillon7]

1. Connects at the spider hose.

2/4 never seen

3. Connects to the side of the iacv at the underside of the intake manifold.

Perfect, thanks!


Just realized I'm missing the PCV valve and hoses coming from it:hitler:

Never again will I buy a "complete motor" from someone.

[NickL]

1. Connects at the spider hose.

2/4 never seen

3. Connects to the side of the iacv at the underside of the intake manifold.

[dillon7]

This information is from looking at my OBD-I S52, which should be pretty similar

1. This connects to a line underneath the intake manifold almost directly underneath the throttle body.

2. That looks like one of the hoses that connects to the bottom of the intake boot

3. I believe there is a line that goes from that stud to the ICV hose

4. no idea offhand

thanks I'll try that

Does #2 have a electrical connector on it? if so it looks like it goes to the charcoal canister.

no electric connector. It goes to the canister that the fuel lines connect to.

if you go on realoem.com and lookup the coolant hose diagrams, they give a pretty clear view of what goes to what.

you have a spider coolant hose that goes from the heater core to the timing cover and has 2 hoses coming from the middle. one will go to your radiator coolant resivoir and one i believe heats the thottle body.

the small nipple on the bottom of the ICV clip that goes into the intake manifold goes to a similar nipple on the PCV clip that goes into the valve cover.

I tried that, got a little lost because the spider hose is from my 86 325e and no diagrams actually show the way my hoses run.

Looking online it said I didn't need to run a hose that heats the throttle body but I'm guessing that extra hose back there is for that because it attatched to my throttle body on my old motor.

I don't have any other hoses or places for hoses to go so I'm still a little confused where that lower radiator hose from the bottom of the reservoir is supposed to go

[mitchlevy7]

if you go on realoem.com and lookup the coolant hose diagrams, they give a pretty clear view of what goes to what.

you have a spider coolant hose that goes from the heater core to the timing cover and has 2 hoses coming from the middle. one will go to your radiator coolant resivoir and one i believe heats the thottle body.

the small nipple on the bottom of the ICV clip that goes into the intake manifold goes to a similar nipple on the PCV clip that goes into the valve cover.

[ryanc88]

Does #2 have a electrical connector on it? if so it looks like it goes to the charcoal canister.

[matthugie]

This information is from looking at my OBD-I S52, which should be pretty similar

1. This connects to a line underneath the intake manifold almost directly underneath the throttle body.

2. That looks like one of the hoses that connects to the bottom of the intake boot

3. I believe there is a line that goes from that stud to the ICV hose

4. no idea offhand