Exactly. Well got the head off and turns out its not corroded! The cylinders look pretty good so scratch the boring it out. Turns out the head is cracked in 3 spots but thats another topic.
Read throught this thread off the BFc and see if you cant gain any knowledge.
Edit* thisone looks good too: http://forums.bimmerforums.com/forum...hlight=stroker
m50 questions!
Collapse
X
-
And also, if you do get new pistons and rods, that means you have to bore out the block = more money!
What i'm hoping to do is get a S50 crank & rods, and 1 shrick cam, and not bore the block, so i'll end up with 2.9 ltrs instead of 3.0.Leave a comment:
-
hmm, I c what you rae saying.. Instead of a s50 crank you use an m52 one, do you reallly need to use the m52 rods? or say the s50 rods if you go with a s50 crank.. why do you choose m52 over s50?Well dude, i got my car running but the m50 needs a headgasket so i may be doing the stroker deal. http://www.e30tech.com/forum/viewtop...&highlight=m50 I like that for some good info. Im not sure what one would do for the software for that set up.Leave a comment:
-
Great deal. I would just take my time and build it up to a 2.8 with some bolt ons and a custom chip, that should be plenty of power. I want a non vanos for my E30. Maybe it's engine will blow up by next summer. I just hope my E34 gets fixed before that happens.Leave a comment:
-
Well dude, i got my car running but the m50 needs a headgasket so i may be doing the stroker deal. http://www.e30tech.com/forum/viewtop...&highlight=m50 I like that for some good info. Im not sure what one would do for the software for that set up.Leave a comment:
-
soo, I just picked up the m50 today.. it seems like it's in good cond. I really do not know were to begin though? I'm thinking go ahead and strip everything down?? And does anybody have any more information about the non vanos 2.9 mini stroker thing?Leave a comment:
-
-
higher compression, using s50 crank, m50 nv rods, m50 pistons, and a 0.098" thick MLS hg from vacmotorsports you end up with like 11.45:1 CR.
Edit: haven't done the math on the m52(328) crank....Leave a comment:
-
328 crank and rods + 325 pistons = High compression 240ish hp 2.8 liter motor.
Do it.
With the non-vanos, you take the intake cam and put it on the exhaust side and buy one schrick or whatever for the intake side, which basically gets you the s50 cam spec. The stock cams are pretty ratty for OE stuff from what i hear.
I really like the idea of the 2.8 liter mostly because the bore is 84mm on the m50 and the s50 has a 86.4mm bore. Not a whole lot but its something to consider. S50 route, you get 240hp or you can use (cheaper) m50/m52 parts and get the same output. Granted you have to use at least 91 octane fuel, preforably higher, with the high comp 2.8. If it was me, i would do the 2.8 or a 2.9 with some aftermarket pistons.
Hope it helps and sorry for the novel.
Yes, it helps alot.. so you are saying I can get a m52 crank, and use the m50 pistons, switch the cams and get 1 extra shrick cam for the intake side.. i will have basically a instant 2.8 stroker?? soo what if i do the same thing, but with a s50 crank?Leave a comment:
-
328 crank and rods + 325 pistons = High compression 240ish hp 2.8 liter motor.
Do it.
With the non-vanos, you take the intake cam and put it on the exhaust side and buy one schrick or whatever for the intake side, which basically gets you the s50 cam spec. The stock cams are pretty ratty for OE stuff from what i hear.
I really like the idea of the 2.8 liter mostly because the bore is 84mm on the m50 and the s50 has a 86.4mm bore. Not a whole lot but its something to consider. S50 route, you get 240hp or you can use (cheaper) m50/m52 parts and get the same output. Granted you have to use at least 91 octane fuel, preforably higher, with the high comp 2.8. If it was me, i would do the 2.8 or a 2.9 with some aftermarket pistons.
Hope it helps and sorry for the novel.Last edited by So Live; 03-29-2007, 04:06 PM.Leave a comment:
-
but then you have to calculate costs for boring, machine work everything.
just to do a stock rebuild on THAT motor (same one I have) would cost your 1500 for bearings, studs, bolts, belts, chains, tensioner's, idler pulley, water pump, new coolant hoses, ALL new gaskets, then you have to throw in a clutch and every, for the stock clutch kit, with a nice discount, will run about 130/150 bucks. Just think about it. That's all I ask. For the S50 crank, that setup will definitely run you over 2k. Oh, and the zion kit is USED parts from a 328. no 3 liter there.Leave a comment:
-
hmm, 4 some reason i thought it's the opposite? if it's non vanos you can, if it's vanos you can't.. what about the zionsville stroker kit???
I mean, it says only 22 hp gain.. i'm guessing that's to the wheels.. well hoping it would be.. But you can't beat 500 bux for crank, pistons, and all that other stuff it comes with.
Leave a comment:
-
you can't use s50 cams on that engine because it's a non vanos engine.Leave a comment:
-

Leave a comment: