Wellll. Interior is back together..... Looks ok but not happy with the carpet. At all..... I mean it looks decent but not what I was going for. Sourced another factory carpet in dark grey. Going to try to dye it black. Will start on a smaller scrap I have before attempting entire thing.
I will try after work to post a few interior shots of the carpet that's in it.
Announcement
Collapse
No announcement yet.
rusted floors, how bad is it?
Collapse
X
-
thank you for the heads up. I will be posting up some more pics prob wed before work. down to my last patch. got the passenger side done yesterday. top has been seem sealed, bottom has been fiber glassed to help blend it all back together.
Got 1 gallon of Second Skin sound deadener in today! stuff looks pretty rugged.
Also got brand new Vibrant 3" resonator!
And.... my favorite part...… The carpet. should be delivered tomorrow morning. Its not factory BMW but ive got high hopes based on research and review. Company is Stock Interiors outta NC. I will def leave feedback after I unbox and check it out.
Leave a comment:
-
OP, it's called "rust encapsulator" made by Eastwoods. You can get it in an aerosol or a quart. I brushed it on with a regular paint brush
Leave a comment:
-
Those patches are coming out great! Very clean work. Yours too, bignslow, nice work recreating the bends in the panel.
I'll have to grab a pic to post, I started into my "74 2002 this weekend. I originally thought I was just patching up a couple holes in the floors... at this point I've cut out the floor, bottom of the a-pillar, and about 12" of rocker panel. When you can see a little rust, it seems inevitable that you'll discover more.
Leave a comment:
-
I guess to be fair to the previous owner I should say I was warned of 2 "Small" holes in that general area and an attempt at patching them. I most def did not expect that but, shit happens. I actually harass him a bit for more insight to what was going on with this thing and hes been super helpful.
Got all the sound deadening out tonight after work, heat gun is by far the best thing going with that stuff. going to wire wheel and tackle the driver side tomorrow while the wife and kiddo are out at a bday party:D
Leave a comment:
-
-
I gotta say, after seeing what other people are dealing with as far as rust its given me some decent motivation to get this done. spent a couple hours cutting and tapping the trans tunnel area patch back in after work last night. I think it turned out very well.
Das Delfin, Is that a roll on rust encapsulator? If so where did you pick it up?
The work your doing looks great!
Leave a comment:
-
OP, here's what I did. My car had some rust from the exhaust heat shield bolts and a lot from a battery that as it sat discharged sulfuric fumes, which then condensed in the atmosphere and settled on the car as an aerated liquid.
I used 18ga cold rolled steel I sourced from a local metal shop, along with Eastwood's rust encapsulator, seam sealer, and for the really nasty stuff, rust converter. My friend Mike was invaluable in guiding me through the process and welding up the patches for me. Making the panels was a lot of fun!
Here's some pics. I'm currently in it right now so some of them don't show full completion
What we started with
Did this one as a lap weld in two pieces as there were too many compound curves to do it in one shot. We used weld-through primer for the inner bits. Once it was tacked in place a good amount we hammered the pieces together to get it to fit tight.
Sharing our victory with beloved friends and family
I can't express in words how good this picture makes me feel. This pic was taken yesterday and only shows one coat of encapsulator and no seam sealer. Soon it will be getting some fresh new paint!!!
The inside before seam sealer. I wire wheeled and coated every bit of rust I could find with the encapsulator.
After.
After going through this I feel 100x more comfortable with this sort of thing. It's been a long process but we're finally at a turning point. Now if only my rear subframe would just freaking come out!
Leave a comment:
-
18 ga. cold roll. I had to anneal the panel so I could shape it and create the curve at the base of the transmission tunnel.
Leave a comment:
-
Originally posted by Sunnyledge View PostAnd welded in place.
That patch looks like it came out mint. What gauge steel did you use?
EDIT: re read the post, 18 gauge!
Leave a comment:
-
Originally posted by SethB View PostHey, congratulations! That's awesome news. My kids have been both the biggest distraction from, and biggest enjoyment with my cars. Looks like you're patching is going well. Might not be a bad idea to try to degrease that area and spray some rust encapsulator around, just to protect it going forward.
Sunnyledge, that's some rust! I bought my ix from a guy in Montreal, the Northeast is brutal!
The plan is to get the patches in place, strip the rest of the sound deadening off the floors and then re spray the entire floor before I put the sound mat down. I have been looking into this product called lizard skin. kinda pricey but an option either way. I may POR15 the floor and lay down dynamat.
My goal is to get the car quieter inside and out, hence why im glad the exhaust is off. Still undecided on how im gonna quiet that down. may run new muffler and add a resonator?
Leave a comment:
-
Hey, congratulations! That's awesome news. My kids have been both the biggest distraction from, and biggest enjoyment with my cars. Looks like you're patching is going well. Might not be a bad idea to try to degrease that area and spray some rust encapsulator around, just to protect it going forward.
Sunnyledge, that's some rust! I bought my ix from a guy in Montreal, the Northeast is brutal!
Leave a comment:
Leave a comment: