e30 s50 turbo opinions!!

[SwiftE30]

where would be a good place to look?

i would look on bimmerforums. i think that would be your best bet to look. just search in parts for sale. or make a thread saying you want to buy "________" insert turbo type here.

that is how i found my garrett.

[BimmerTim]

Siemens 60lb injectors
Stock FPR
Stock Fuel Pump
Stock Pistons
Stock Headgasket
Stock Plugs and Coils

There was a lot of room for me to make more power, easily. I was just over the car, and sold it.

[warioware]

FWIW, I ran the GoodnTight manni, and a Holset HX35 on my s50.

I did 325rwhp @8psi on a crap tune.

thats pretty good i'll probably end up going with the HX35 and just a mild tune what kind of injectors were you running?

[BimmerTim]

FWIW, I ran the GoodnTight manni, and a Holset HX35 on my s50.

I did 325rwhp @8psi on a crap tune.

[warioware]

The HX35 will work on my manifold. Check this thread for pics ----->http://www.r3vlimited.com/board/showthread.php?t=227950

I can make a package deal if you want the chip and manifold together.

I actually bought the manifold from you off ebay a couple of days ago lol

[M-technik-3]

Get a miller WAR chip for tuning, and a properly welded manifold. Amazing what people pass off on forums these days as "quality"....

Lets not get in to the customer relations, or lack of it when it comes to them. Glad you like there product.

Otis has been doing manifolds for quite some time as does Jon Volk of 666Fab.com

[shiboujin]

+1 for Mr. Good and tight. I've had 3 M50 turbo manifolds in my E30. His fits the best by far. Easy access to all but like 2 bolts. But even those 2 bolts aren't that bad compared to the other manis.

Also +1 to that manifold working with an HX35. I have an HX35 and a good and tight mani. Can snap pix if you want.

the chip will work too. If you don't want to mess with DIY stuff, just get a chip and be happy. Retunes are just kind of a pain. Also, you have to run an ugly maf :-p

[Good & Tight]

do you have any pics? and will it work with the blunttech good n tight manifold?

The HX35 will work on my manifold. Check this thread for pics ----->http://www.r3vlimited.com/board/showthread.php?t=227950

I can make a package deal if you want the chip and manifold together.

[warioware]

I have a turbo chip tune for the stock DME from NickG that is for a draw through setup using your stock MAF and a set of 36# injectors. It's good for up to 9psi. $500 shipped for the chip tune if your interested.

hmmm i might be interested would i need anything else like any sensors??

[dubseven]

Get a miller WAR chip for tuning, and a properly welded manifold. Amazing what people pass off on forums these days as "quality"....

[Good & Tight]

I have a turbo chip tune for the stock DME from NickG that is for a draw through setup using your stock MAF and a set of 36# injectors. It's good for up to 9psi. $500 shipped for the chip tune if your interested.

[Hey_You]

why megasquirt when the stock ecu is more than fine

I would say so. Not a very smooth graph though. I think it could still be worked upon

[warioware]

so then you recommend just getting a tune? from TMS or who?

[warioware]

this. i'll be putting one on my m20 if i don't end up going m50nv (which will have a gt35r but only because it was given to me. if that wasn't happening, i'd go hx35)

how much for the gt35r ;)

[Dominic49]

as far as engine management im leaning towards MS im still not exactly sure but i've heard a member sells them PnP

why megasquirt when the stock ecu is more than fine