Fuse 10 keeps popping....help me read the wiring diagram!

[BMWManiac]

Keep this thread posted, please. I don't have my new switch yet, but today I'm going to pull the wires through and check them

[MrSlacker]

Turned out my reverse wires were completely cut in half somehow! Hopefully fuse 10 will no longer be an issue

[BMWManiac]

WOAAA!!!

My fuse #10 started randomly blowing one day. Would happen sometimes after an hour of driving, sometimes after 20min or it was fine.

Then after a week it has been just fine. I recently noticed that my reverse lights don't work!

Now I am getting random check engine light that goes away right away.

Going to try a new switch and check the wiring as well... THANKS!

Yes, check the switch (passenger side of trans) and you should see two wires to connect to two prongs on the switch!

[MrSlacker]

WOAAA!!!

My fuse #10 started randomly blowing one day. Would happen sometimes after an hour of driving, sometimes after 20min or it was fine.

Then after a week it has been just fine. I recently noticed that my reverse lights don't work!

Now I am getting random check engine light that goes away right away.

Going to try a new switch and check the wiring as well... THANKS!

[BMWManiac]

Glad you found the problem, same happened to me with a Vert I bought a while back, the wires for the reverse light run on top of the tunnel then under the carpet by the driver seat and then straight to the fuse box, take kick panel off and make sure the wires are OK to there. My wires when they touched melted another 4 wires.

Great....did I mention how I love wiring!

[hyperE30]

I figured as much....would you happen to know if they are secured by a zip tie on top of the transmission tunnel? I'm curious if I can pull them back through or if it is hard to with the transmission mounted!

Glad you found the problem, same happened to me with a Vert I bought a while back, the wires for the reverse light run on top of the tunnel then under the carpet by the driver seat and then straight to the fuse box, take kick panel off and make sure the wires are OK to there. My wires when they touched melted another 4 wires.

[BMWManiac]

That's it. It is a very common issue. Short to grounds cause it to blow immediately.

Good, I replaced my main harness because of this and an ICV issue I am having with my MS2 setup....

[M-technik-3]

I want to bump this.....I think I found the issue. My reverse switch in the transmission basically fell apart, leaving my reverse wire connectors touching each other.....

While researching the reverse light switch, that I now need, I read to check fuse #10! So I think I might have found the culprit.

Now, having said that, where do the lines to run from? The shifter console to underneath the dash? I want to make sure the wires are fine as well.

That's it. It is a very common issue. Short to grounds cause it to blow immediately.

[BMWManiac]

The wires for the reverse switch run under the console and down through the rubber shifter boot.

I figured as much....would you happen to know if they are secured by a zip tie on top of the transmission tunnel? I'm curious if I can pull them back through or if it is hard to with the transmission mounted!

[jlevie]

The wires for the reverse switch run under the console and down through the rubber shifter boot.

[BMWManiac]

I want to bump this.....I think I found the issue. My reverse switch in the transmission basically fell apart, leaving my reverse wire connectors touching each other.....

While researching the reverse light switch, that I now need, I read to check fuse #10! So I think I might have found the culprit.

Now, having said that, where do the lines to run from? The shifter console to underneath the dash? I want to make sure the wires are fine as well.

[BMWManiac]

It's a sit and spin kind of thing. Twist one way on the top, the other on the bottom. :-D

I tried last night and wouldnt work....overcomplicated things but got it to unfasten this morning:)

[george graves]

How does the C101 connector, disconnect?

It's a sit and spin kind of thing. Twist one way on the top, the other on the bottom. :-D

[BMWManiac]

Thanks, George...will do

How does the C101 connector, disconnect? I have a replacement harness coming anyways and it would be easier for me to pull the wiring harness, and inspect all the wiring to see what happened

[george graves]

The Bentley is a poor diagnostics tool for electrical stuff. The e30 ETK is much better.

If it was me......I would pulling up the ETK for your model and year, to see what fuse 10 powers... Then I would unplug or disconnect everything connected to it, and plug one in at a time to see what is blowing the fuse.

It could be anything. With out looking at the diagrams I can't help too much. But the oxygen sensor heater is in the area of the down pipe...that is one of the things I would look at first.