Announcement

Collapse
No announcement yet.

Z3M Trailing arm Geometry (Different?)

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Z3M Trailing arm Geometry (Different?)

    Are Z3M Trailing arm Geometry the same as normal E30?


    I have a set on my car and out of the box they have 1* of toe out per side.
    About 1/4 inch of toe out total in a factory subfame.

    I have redone a subframe using POSILOK adjuster vs eccentrics for more adjustability. With toe in MAXED, I am at almost zero toe.

    Thoughts?
    Last edited by moatilliatta; 08-23-2018, 01:15 PM.
    sigpic
    1999 BMW 318Ti/M Hellrot Msport DD/Fun car
    1/2 1987 BMW 325is/M Future Spec e30 (track prep'd)
    1994 530It/A Alpinewise III Traded out
    1988 BMW 325ix/M Diamond Schwartz Recently sold :/
    1986 BMW 325e/m Bronzit Beige Metallic

    Get Involved!
    www.bluegrassbimmers.org
    OKI BMW Facebook group

    BMWCCA Member# 436428

    ZAKSPEED
    Quality BMW service "street, track, race"?
    Email: Zach Ketring @ Zach@Zakspeed.us

    #2
    Iíd question the subframe, and the straightness of the arms, the pic up points are supposed to be the same iirc. Sorry not much help, but some thoughts if nothing else


    Sent from my iPhone using Tapatalk
    ...what hasnít been done to an m20 yet?

    m20 Oil Stencil

    Comment


      #3
      I swapped subframes. No real change.

      Both arms have quite similar toe. Odd that they would be equally bent.
      sigpic
      1999 BMW 318Ti/M Hellrot Msport DD/Fun car
      1/2 1987 BMW 325is/M Future Spec e30 (track prep'd)
      1994 530It/A Alpinewise III Traded out
      1988 BMW 325ix/M Diamond Schwartz Recently sold :/
      1986 BMW 325e/m Bronzit Beige Metallic

      Get Involved!
      www.bluegrassbimmers.org
      OKI BMW Facebook group

      BMWCCA Member# 436428

      ZAKSPEED
      Quality BMW service "street, track, race"?
      Email: Zach Ketring @ Zach@Zakspeed.us

      Comment


        #4
        I installed a pair of z3m trailing arms and had similar toe issues. I chalked it up to the arms being from a theft recovery car.

        Maybe they are slightly different due to the (small) width difference between the subframes?

        I ended up welding in the adjustment plates and IIRC had to make the slots larger to get full articulation and back into spec. They also loosen so I recommend tack welding them once set.

        Comment


          #5
          Being that both Z3M trailing arms were about identical out, it led me hard to believe that they were NOT damaged.

          I used the serrated style adjusters from IE. I've got tired of worrying about it and hopefully this is a new solution to loose trailing arm adjusters.

          They've been modified with Grade 8 1/2 Bolts, bevel washers, and a nut welded instead of the serrated end tapped/ threaded.

          I couldn't find Metric hardware to work properly, Fits the sleeves of most bushings better also.

          TC01 Subframe Rear by Zachary Ketring, on Flickr

          TC01 Subframe Rear by Zachary Ketring, on Flickr

          TC01 Subframe Rear by Zachary Ketring, on Flickr

          TC01 Subframe Rear by Zachary Ketring, on Flickr
          Last edited by moatilliatta; 10-21-2018, 05:23 AM.
          sigpic
          1999 BMW 318Ti/M Hellrot Msport DD/Fun car
          1/2 1987 BMW 325is/M Future Spec e30 (track prep'd)
          1994 530It/A Alpinewise III Traded out
          1988 BMW 325ix/M Diamond Schwartz Recently sold :/
          1986 BMW 325e/m Bronzit Beige Metallic

          Get Involved!
          www.bluegrassbimmers.org
          OKI BMW Facebook group

          BMWCCA Member# 436428

          ZAKSPEED
          Quality BMW service "street, track, race"?
          Email: Zach Ketring @ Zach@Zakspeed.us

          Comment


            #6
            That looks quite beefy. I must have had an older smooth set, the serrated ones weren't on my radar.

            I made some sharpie marks on the adjusters as well for a quick visual check that nothing had moved. They haven't moved after years of track use, so hopefully you will have it made in the shade.

            Comment

            Working...
            X