Repaint/Alpha-n/and more... E30 CONTENT

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • uofom3
    replied
    Originally posted by CleanAzzE30z
    My fucking Innovate system has never worked correctly. Yours I see is working well. Looks good!!!


    Mariano
    Mariano run it disconnected from the MAXX. Just run the MAXX with lamda off and then connect the laptop to both the innovate logger software and the maxx. It works fine for me. Do you have an LC-1?

    Leave a comment:


  • YAN-3
    replied
    Ted i need to do a oil filter relocation as well for my box, did you use the summit kit?

    Leave a comment:


  • CleanAzzE30z
    replied
    My fucking Innovate system has never worked correctly. Yours I see is working well. Looks good!!!


    Mariano

    Leave a comment:


  • uofom3
    replied
    Originally posted by YAN-3
    more videos please. by the way is the box a 15cm or the bigger 17cm version?
    Can't remember... I'd have to look it up but i'm pretty sure it's the bigger version. I also believe it's 48mm throttles.

    Leave a comment:


  • uofom3
    replied
    Originally posted by Mr. Anderson
    I'm sorry, Ted. I had to. I could not help myself.

    lol

    That is funny shit.

    Leave a comment:


  • Jand3rson
    replied
    I'm sorry, Ted. I had to. I could not help myself.

    Leave a comment:


  • YAN-3
    replied
    more videos please. by the way is the box a 15cm or the bigger 17cm version?

    Leave a comment:


  • nefarious7907
    replied
    Bad ass.

    Leave a comment:


  • uofom3
    replied
    So... it's been a while since an update and since some things are nearing completion... i figured I'd post up here and dig up the old thread.

    Finally, I got around to instaling my Innovate LC-1 WBo2. This gave me problems at first because I was trying to get it to connect to my 1st gen. MAXX system (doesn't have a direct out for WBo2 application). Finally, I said F that and just wired it in on its own, and run the MAXX A/N with lambda off. I'm told this makes no difference as ultimately with a good map I shouldn't need to lambda sensor correction and I don't have a cat-converter, so there is not reason to worry about getting too rich.

    So, I'll start with the AFR gauge. It's the XD-16 gauge from Innovate that works with LC-1 WBo2. I used input from Chris, and decided to mount it in the center dash vent.





    And a picture of my accompanying "rice rocket" gauges



    So, with that done, this is what she looked like from the front



    Got torn apart to prep it for paint, but that never really happened. Now, a few pannels are sanded, and it generally looks like a POS from a paint standpoint. Once I get it running and tuned, the painting will commence.

    Engine bay buttoned up - there will be a few changes though. I have a silicon hose on order to replace the accordian hose that came with the kit (YES, I AM AWARE OF WHY THEY USE THE ACCORDIAN HOSE. YES, I HAVE DONE MY REASEARCH. NO, I DON'T WANT ANY OTHER KIND OF ACCORDIAN HOSE. I HAVE CONFIRMATION THIS WILL WORK FINE. THANK YOU.). That should be here tomorrow. I also need to make the final plastic bracket to mount the brake fluid resevior to the strut tower, and get my remote oil filter kit pieced together. The oil filter relocation will probably get solved next week, and i'll make a new thread regarding it.



    I powdercoated the throttle bracket to look more factory and not take away so much attention from the box



    Here you can see the custom bracket with the oil filter relocation and the Air/Oil seperator for venting the crank case vapors. The A/O seperator may get moved down to the place that the carbon canister is currently residing to get it out of the way if I decide to remove it.



    So then I got it looking more like a car again...



    Thought this pic was cool



    Quick shot of the drivers side - lots of information (good thing they all have warning lights!) - and note the tach (proof it works! ;))


    Finally it looks like a car again, but without my e3 front/rear spoilers :( and YES, the rice rocket hood will be painted body color when everything is painted.


    engine bay



    3/4



    interior passenger side cleaned up



    driver side interior cleaned up






    Final shot of the box



    And, a working car again :)




    Need to bleed the brakes out tomorrow, and once that is done I can hopefully get it tuned up well enough to drive it to the meet on saturday. Probably won't make it on a long drive with the group, but it will at least limp over there :)

    More to come as the oil filter gets sorted out, stuff on the tuning process, final brackets are made, and the silicon hose gets here.

    Cheers,
    Ted

    Leave a comment:


  • Widm3r
    replied
    Congrats on getting it running man, i cant wait to see it when its all said and done!

    Leave a comment:


  • 4ce30
    replied
    sweet! i bet your stoked... cant wait for it to be done!
    -Brandon

    Leave a comment:


  • uofom3
    replied
    video evidence (hopefully this works)

    Leave a comment:


  • nefarious7907
    replied
    Hey at least you have a garage

    But congrats on getting that beast running.

    Leave a comment:


  • uofom3
    replied
    IT RUNS!

    I can't remember the last time it ran, but it idles (albeit a bit rich) in the garage.

    pre-startup pic:


    I think I have the worst garage working conditions on the board but it works!

    Long story short, it is finally alive and I am awaiting a few things to come back from powdercoat before I do the **final** assembly. I'm also expecting a WB02 for xmas so then tuning can commence next week!! I am beyond stoked that the thing finally runs. Many more pics to follow once the parts come back from the powdercoaters and I'll post a video of it comming to life here in a bit once I get it off the movie camera.

    Leave a comment:


  • e30325ic
    replied
    Nice work and nice car. Love the M3's. Keep the updates comming.

    Leave a comment:

Working...