Repaint/Alpha-n/and more... E30 CONTENT
Collapse
X
-
it's ALMOST ALIVE!!!
Tomorrow I will spend a good deal of time making the final adjustments to the TPS and fire the thing up.
I decided to ditch the bracket for now. My friend in town who also has an m3 (and is an engineering guru) is using CAD to make modifications to my proposed bracket. We are going to weld it up and powdercoat it to make it look very factory. he also purchased the same oil filter relocation that I did, and is making modifications to it that I will do on my car - so I am forgoing the relocation for now as well. Both should be completed by mid-december once he welds up the brackets and we get them and other parts out to powder coat. Here is a quick diagram that I made and sent to him of the bracket idea I had... I'll see if he'll give me the final CAD and I'll post that too for other people to maybe use as an idea in the future.
So, with that in mind, today I just wanted to button it all up and simply get the car started. Everything under the hood is SUPER temporary. This stuff is all snugly in place and "functional"... but it looks like hell. Once the bracket is fabricated, it will look 100% factory approved (or damn near). This is how I setup the bottles on the side:

test fitting the box:

GREAT SUCCESS!

the temporary product that will allow me to get the car idling and partially tuned (or at least driveable to get it painted):

I then spent a little bit of time getting the wiring sorted out inside because the laptop would not read the max. Turned out, I put a wire in the wrong slot, fixed that, and now we are in business. The MAXX is reading the air temp sensor and the TPS, so I am pretty confident that I did that properly.
I'm waiting to start it tomorrow as it got dark and effin cold at 5:30 tonight... so later this evening I will spend a good amount of time reading the tuning information so that tomorrow I will be able to get it up and running (hopefully).
So fingers crossed it will start tomorrow. This has been a hell of a project for an admittedly relatively novice wrencher. If I can get it running, I will feel pretty accomplished. Much more tomorrow.Leave a comment:
-
^
read the post... I'm having braided lines and stainless fittings made tomorrow.Leave a comment:
-
That is exactly the same as the Summit brand one down to the lettering.
As for the hose though I think its junk, it has split on me twice, and now one of the lines has a tumor. So when you do get it installed check the lines periodically. I am going to be swapping over to braided steel lines shortly, my tolerance for rubber lines has run out.Leave a comment:
-
So this process might interest some people on the board. Today I took care of putting in my oil filter relocation kit, or rather mocking it up so I can have some better hosing made for it tomorrow. This is the kit that I purchased: http://store.summitracing.com/partde...5&autoview=sku
The way they have these hoses setup is not very sturdy, so tomorrow I am going to go have some braided hose with better fittings made to fit into the same openings as on this setup. This will not only look better, but also perform better and be sturdier than what is supplied with this kit. I think I can get the cost down to about $160 to $170 total vs. 300+ for an AN fitted setup.
First, a pic of the kit:

And the mess that it is going to live behind:

First thing to do is find out whether or not you need the adaptor plate for your oil filter housing. In the case of the s14, you don't with this kit.
Secondly, you need to figure out what size adaptor you need. The kit comes with four, I used the second to the smallest adaptor to get the motor-side of the kit to mount.
Prepped with teflon tape:


Mounted:


Next, some shots of the adaptor. The adaptor has the screw that goes into it that the oil filter will eventually spin onto. Add teflon tape, and screw that in.





A few shots of where it is going to sit after the bracket is made. I am using this position because I cannot fit it along the framerail given clearence issues with the CF snorkel.


Next, my air oil seperator. This thing is really high quality; I'm very pleased. It will be used only to vent the crankcase vapors, but I could use the other side that is plumbed (will be plugged) for something else in the future.
Pics:


The bottom has a tap to drain the oil that will collect in it over time:

And this is the approximate location of the goods once I made a bracket for it all:

The bracket will hopefully be done over thanksgiving weekend, and once that is done, I can just connect everything up and start the car hopefully by a week from today if I get the line back from the supply company in a timely manner. The only small things that I have to accomplish are modify the air filter and put in the non-cruise control pannel in the interior. Interior wiring is done to the point of being able to run the car.
More in a week. Hopefully if this hose setup that I am having made turns out well, I could have more made if others are interested in making this affordable kit look/perform better.Leave a comment:
-
My 87 e doesn't have cruise as well. Keep moving on it. I want to actually see this car at the picnic this year. If its in primer I don't care...Leave a comment:
-
My 84 325 does not have a hole for the cruise control.
Everything looks like its coming together at a decent, keep tooling man.Leave a comment:
-
OK... so, got the box to fit by shimming the driver side motor mount slightly.
pictures of the spacer


installed

Picture of the parts to come out today

Removed

interior controls removed


Picture of the mess at large:

Now I have lots of empty space up front for my bracket that will hold the fluids/ air/oil seperator, and the oil filter relocation kit. I'm also seeing if BMW makes a cover for under the steering column that doesn't have a hole in it for the cruise control (I would guess an early 318i might not have it or something). At next update hopefully will have:
-bracket made
-oil filter relocation complete
-box on
-interior buttoned up
just waiting for parts to arrive! Although it doesn't look like it, this project is finally starting to see the light at the end of the tunnel. This thing should really start taking shape next week.Leave a comment:
-
Well then that is really odd... I wouldn't expect the boxes to be different in dimensions.Leave a comment:
-
Possible... I will check into it tonight by measuring the MC's... but as I recall there is zero difference in the size of the casting for the two MC's. The difference is a two mm large cylinder.... the only way you can tell the difference between the two is the number stamped on the top of the MC.Leave a comment:
-
I'm betting it's the larger MC thats the problem. I do not have any contact issues with the stock MC with John's airbox, but it does have slight contact the hood. I'm going to use the lower 740i mounts to solve that issue.Leave a comment:
-
Taller motor mounts? They certainly cannot go lower... and from what I understand the 740 mounts actually lower the motor... Jake has like 2 inches of clearance on his so I cannot see what the problem is with mine.Leave a comment:

Leave a comment: