Repaint/Alpha-n/and more... E30 CONTENT

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • UNHCLL
    replied
    Originally posted by uofom3
    So I then went to prepare to finish up the airbox, and we ran into a problem. I got the box to fit on the TB's, but now it's contacting the brake master cylinder. This is preventing the airbox from properly seating on the TB's. So either the BMC is not sitting properly (doubtfull), the fact that I have a 25mm MC is a problem, or if the trumpets are simply too long. I'm a bit perplexed by this as the motor is brand new (less than 1200 miles) and done with all factory parts (that would impact the mounting of this part). Also, all of the stock parts fit perfectly, so I see no reason why this shouldn't fit as well.
    Search MAXX threads on S14.net.
    Once you get through all the crap, I think it's a common issue. Most end up changing motor mounts to prevent rubbing on either the brake MS, or the hood.

    -C

    Leave a comment:


  • uofom3
    replied
    minor work completed recently... with much more in store soon that will be more noticeable.

    First - put the body back together so that it will be driveable to get it tuned enough to go to a paint shop under its own power. Before/after:







    quick shot of part of the family fleet

    the interior mess as I found it:

    FINALLY got the wiring finished up with the help from a friend of mine:


    I still have to "finish" the wiring with some shrink wrap and other protective stuff; but it's done.

    So I then went to prepare to finish up the airbox, and we ran into a problem. I got the box to fit on the TB's, but now it's contacting the brake master cylinder. This is preventing the airbox from properly seating on the TB's. So either the BMC is not sitting properly (doubtfull), the fact that I have a 25mm MC is a problem, or if the trumpets are simply too long. I'm a bit perplexed by this as the motor is brand new (less than 1200 miles) and done with all factory parts (that would impact the mounting of this part). Also, all of the stock parts fit perfectly, so I see no reason why this shouldn't fit as well.

    How the engine bay was left:


    I have on order a air/oil seperation bottle that will allow me to vent the crank case vapors straight to the canister as opposed to being sucked back into the motor (reduce detonation).

    My buddy also is helping me mock up my engine bay to ultimately built new fluid reseviors out of AL that will sit on an AL bracket that mounts where the AFM used to be. I want to do all of my rounting for the PWS fluid, brake fluid, and oil filter relocatoin with braided line/AN fitting... but we will see how that goes cost wise. Some stuff my just be good rubber/reinforced hosing in areas where heat/pressure is not a major concern.

    Bottle should be here soon... still awaiting a reply from the airbox supplier on what I will need to do/replace/return/ect.

    Leave a comment:


  • White Nightmare
    replied
    Originally posted by UNHCLL
    Here are some words of advice for you Mr. Beagle...


    The elitist "I know more than you and get better deals, but I'm not telling how/why/where/what" attitude is about as lame as the re-runs of Punky Brewster on Saturday morning cartoons.

    Here's another tip from someone older and "similar" to you.... Just because your Dad/Uncle/Sister/trans-gender once removed aunt/(insert relation of choice) has a performance shop, doesnt equate to you being a high and mighty know all king above everyone else.

    Trust me, I've been there, had that attitude, and it's lame. Act humble, be mature, and don't be such a little prick to everyone. It's really unbecoming... If you wan't be helpful, give suggestions without alluding to underlying information.

    But hey, what do I know... and you won't listen until you're 22+ years old anyways.

    -Chris

    Finally someone said it..

    Leave a comment:


  • CleanAzzE30z
    replied
    Yeah its tough drilling the beautiful snorkel eh? Im glad I wasnt around. Youre crude thing for the fluid reservoir looks much better than mine.

    Mariano

    Leave a comment:


  • uofom3
    replied
    ^
    Wish i was comming too guys - but with finals and the car clearly not being roadworthy it just isn't happening. It will be a different story in 08' for many reasons!

    And stickers can be changed! I have something else in the works but this is temporary.

    cheers!

    Leave a comment:


  • DarkWing6
    replied
    Originally posted by uofom3
    Have fun at the picnic guys!
    Wish you were here. :(



    Looks great, but IMO I would lose the sticker.

    Leave a comment:


  • uofom3
    replied
    on topic:

    So i plumbed the air temp sensor for the a/n. I was nervous to drill into the CF but I was told that i would be just fin, so i got out thedremmel and got after it.
    Pilot hole with dremel

    drilled out to spec

    tapped

    and instaled



    Secondly I made a crude bracket for the brake fluid resevoir


    And now I found this piece of hosing in my garage to use to help splice a few different hoses together as will have to take care of to re-route to the new holes on the CF box


    This piece is going to be invaluable to making this work.

    Finally - I added the sticker to the box:)


    This weekend more will take place - likely on the paint side. Have fun at the picnic guys!

    Leave a comment:


  • UNHCLL
    replied
    Originally posted by Mr Deagle
    There are better/cheaper options for a rpm vs tps setup on an s14
    Here are some words of advice for you Mr. Beagle...


    The elitist "I know more than you and get better deals, but I'm not telling how/why/where/what" attitude is about as lame as the re-runs of Punky Brewster on Saturday morning cartoons.

    Here's another tip from someone older and "similar" to you.... Just because your Dad/Uncle/Sister/trans-gender once removed aunt/(insert relation of choice) has a performance shop, doesnt equate to you being a high and mighty know all king above everyone else.

    Trust me, I've been there, had that attitude, and it's lame. Act humble, be mature, and don't be such a little prick to everyone. It's really unbecoming... If you wan't be helpful, give suggestions without alluding to underlying information.

    But hey, what do I know... and you won't listen until you're 22+ years old anyways.

    -Chris

    Leave a comment:


  • Ray Smoodiver
    replied
    Back on topic pls?

    Leave a comment:


  • Mr Deagle
    replied
    Originally posted by FredK
    Yeah for standalone, that is cheap!

    There you go

    retail is like 800-900 usd, you just need to build a harness and buy a tuning interface

    32x32 table, A/N or Speed density


    Oh and, if the e30 m3 uses a bosch 35 pin ecu connector, then you can use your factory harness with re-pinning it

    Leave a comment:


  • FredK
    replied
    Yeah for standalone, that is cheap!

    Leave a comment:


  • Mr Deagle
    replied
    Originally posted by FredK
    U SEE MY STANDALONE? MADE IN ITALY. YOU KNOW HOW MUCH IT COST? MORE THAN U CAN AFFORD.


    its actually really freaking cheap, $650 + shipping (my cost)

    Leave a comment:


  • backtrail69
    replied
    Originally posted by cramer
    If you've got any tips, please PM them my way. Box should be here next week and I may attempt an install before the picnic...
    Ur crazy..

    Leave a comment:


  • cramer
    replied
    Originally posted by uofom3
    Got the box to fit - long story that I can answer in PM regarding that.
    If you've got any tips, please PM them my way. Box should be here next week and I may attempt an install before the picnic...

    Leave a comment:


  • CleanAzzE30z
    replied
    I just sold my Sparco bar yesterday.


    Mariano

    Leave a comment:

Working...