Looks great! Nice work on repainting the pedals too since they always seem to get scuffed above the pads.
Announcement
Collapse
No announcement yet.
E30 1990 Alpin-weiss 2 - M50B25 - E30 M3 5LUG
Collapse
X
-
The car had small case 4.44 diff so i bought 188mm 3.46 LSD and installed it with fresh Motul oil
The new vs old small diff
Now its manual and has LSD diff,, it just needs more powerful engine now!!
Bought that bracket from Garagistic
Thats to large
Found that one at Costco,,, much better!
Installed
Modified the exhaust tips just for the look
Ready for that summer :)
BMW E30 M3 - S50B32
www.e30.is
Comment
-
I just bought that M50B25 vanos engine from E34 525IX
going to refresh it a little before i install it
BMW E30 M3 - S50B32
www.e30.is
- Likes 1
Comment
-
Bought Recaro keiper seats
They are great but i hate these gray doorpanels
So i got black door panels :)
BMW E30 M3 - S50B32
www.e30.is
Comment
-
Time for the M50 engine swap!
I started on the wiring,, e30 C101 plug/pigtail on the engine loom side
Had to remove loats of wires cause that wiring loom is from an slushmatic e34
E30 C101 plug ready
I used a brakebooster from Porsche 944
944 booster VS orginal e30 booster
Installed the brakebooster
Changed the oilpan, pickup etc..
Bought redlabel DME
there is some stupid aftermarket chip in it,,, maybe its for higher revs or something.. meh lets give it a try
That motor is old and driven 270.000km so i bougt alot of new stuff
Valvecover gasket
Valvecover nut gaskets
Oil cap
Fan belt
Oilfilters
Thermostat
Vaterpump
Seal for throttlebody
Intake manifold seals
Pilot bearing
Crankshaft seal front
Crankshaft seal rear
Exhaust manifold seals
Spark plugs
Bosch oxygen sensor
Fan belt tensioner
fan belt wheels
Oilfilter housing gasket
Water height sensor
Fan clutch
Lower radiator hose
Upper radiator hose
Clips for fanshroud
Brown cooling temp sensor
radioator
Exhaust manifold studs
Exhaust manifold nuts
waterpump pulley
6pcs new ignition coils
6pcs ignition coil extensions
air Inntake hose for e36
upper hose for idle valve
lower hose for idle valve
cap for coolant tank
dipstick
dipstick pipe
Flywheel bolts
Ireland Engineering poly engine mounts
Ireland Engineering poly gearbox mounts
6cyl instrument panel chip
4pcs plastic covers for engine
Thermostat housing
valvecover nuts
probably forgetting something..
E34 oil pan install
The valve cover is horrible so i got it powdercoated
Valvecover on, new sparkplugs, new ignition coils, thermostat hosuing, waterpump, waterpump pulley etc…
Disgusting rusted exhaust manifold so i bought equal length stainless headers
Sandblasted the oil filter housing and added oil temp sensor for e30 m3 cluster
New belt tensioner and other wheels
Time to take that shitty M40 out
I cleaned the engine bay
M50 ready for install with gearbox
Custom engine mounts
Fan shroud
New dipstick and dipstick pipe
oil and antifreeze,, bought 20L of oil because im going to flush the engine 2 times.
Down it goes
Fanshroud, fanclutch, radiator, hoses ready
The car runs now, but i need to finish some minor things in the enginebay and make some exhaustBMW E30 M3 - S50B32
www.e30.is
Comment
-
Bought new hoses for valve cover breather
bought that cover
Looks better!
Now everything is almost ready in the enginebay area, i hate that ugly red air filter,, im going to replace it later for another one.
6cyl chip for the cluster
6cyl chip installed, Oil temp meter connected and speed signal to DME for vanos
My Mtech1 steering wheel was looking bad so i took to a guy who fixed it with new leater! :D
Also leather handbrake
Then i got that package from Ukraine
in the package where MHW style taillights
Cleaned that well before fitting
Now everything is ready but not the exhaust
BMW E30 M3 - S50B32
www.e30.is
- Likes 3
Comment
-
Your 316i is very much like mine , almost nothing from a 316 is left in there hahaha.
V nice engine mounts , it seems you got better clearance from the front of the engine to the radiator tbh !
Car needs to go a bit lower , but i guess streets are very bad haha
btw , got the same equal length headers on my m52 .. only bad part is clearance with the engine mount for the front downpipe , but nothing that a custom exhaust can't do .
keep the good updates!
Comment
-
Originally posted by QuiqueUy View PostYour 316i is very much like mine , almost nothing from a 316 is left in there hahaha.
V nice engine mounts , it seems you got better clearance from the front of the engine to the radiator tbh !
Car needs to go a bit lower , but i guess streets are very bad haha
btw , got the same equal length headers on my m52 .. only bad part is clearance with the engine mount for the front downpipe , but nothing that a custom exhaust can't do .
keep the good updates!
You need to make a thread about your car! :)
but yes these custom engine mounts give more clearance between engine and radiator,, thats why i can run fan shroud and orginal fan clutch
i'll definitely lower it a bit more when i buy adjustable suspension, but still the roads are not that great here :/BMW E30 M3 - S50B32
www.e30.is
Comment
-
very nice build ! love to see more than just flashy wheels and steering wheel in the 'build" .
Cheers!Mtech1 v8 build thread - https://www.r3vlimited.com/board/sho...d.php?t=413205
OEM v8 manual chip or dme - https://www.r3vlimited.com/board/sho....php?p=4938827
Comment
-
Time to make 3" stainless exhaust system!
New OEM exhaust hangers
New oxygen sensor from Bosch, stainless weld on nut for oxygen sensor, bolts and nuts
Stainless "Y" pipe 2x2.25" to single 3"
Laser cutted stainless flanges
Oxygensensor, stainless 3" V-band clamp and flanges
2.25" and 3" pipes from stainless
Vibrant 1047 muffler with 3" Inlet and 2x 3.5" outlet stainless
Vibrant 1142 stainless resonator 3" inlet and outlet
Nice stuff
Making that "Y" thing from the headers and down to 3"
"Y" pipe almost ready
"Y" pipe ready
Now its the rest
Almost there
Bought that airfilter since i hate that red ricer air filter
Much better
Exhaust finally done!
And its bolted in
Oxygen sensor
Here is a small video of the sound,, will make better video in the summer
BMW E30 M3 - S50B32
www.e30.is
Comment
-
Same exhaust setup on my M52 car, just with stock OBD2 headers.
I found it a little loud for me, but damn it sounds good.Originally posted by priapismMy girl don't know shit, but she bakes a mean cupcake.Originally posted by shamesonUsually it's best not to know how much money you have into your e30
Comment
-
Originally posted by Northern View PostSame exhaust setup on my M52 car, just with stock OBD2 headers.
I found it a little loud for me, but damn it sounds good.
do you have a soundclip? :)BMW E30 M3 - S50B32
www.e30.is
Comment
-
Originally posted by Mazi! View Post
Nice
do you have a soundclip? :)
After turbo with external mic under the hood:
https://youtu.be/tJzrilZ7d7QOriginally posted by priapismMy girl don't know shit, but she bakes a mean cupcake.Originally posted by shamesonUsually it's best not to know how much money you have into your e30
Comment
-
Originally posted by 2mAn View Post
Quique when will we see a build thread on yours?
You need to make a thread about your car! :)
but yes these custom engine mounts give more clearance between engine and radiator,, thats why i can run fan shroud and orginal fan clutch
i'll definitely lower it a bit more when i buy adjustable suspension, but still the roads are not that great here :/
v nice , big fan of those ! i just run a pusher fan, it works great but i do have a bit of problems with the temp sensor for it haha.
yeah same , i wish i could go lower on my car , but it looks decent !
btw , v nice exhaust you got there ! keep updates coming !
- Likes 1
Comment
Comment