my e30! very sloooooooow progress.

[E30NJ]

its a good start!

[efficient]

Gonna bump it. Car has been running good. Car is not a show car but people give me thumbs up all the time.

[efficient]

got an update finally installed my motor. i would have done more but the sun was strong today. pretty happy for doing my first motor pull and putting it back in.

Untitled by clean3two3, on Flickr

Untitled by clean3two3, on Flickr
now i just need fuel line, oil, trans fluid and new sensors and wire harness. eventually i want to get a s 3.73 diff.

[e30m20TurbO7]

Have the crank polished , if its not perfectly round , or if your clearances aren't in check you will create a knock

anyone know if i can just put new bearings on the crankshaft without doing anything to the crankshaft itself?
and
the pistons can i reuse the pistons but put new piston rings on them without honing the block?
any advice?

[efficient]

anyone know what kind of throw out bearing i should buy for my 90 325is motor with a g260 from a 86 es transmission. i have the flywheel from the is motor but kind of confused on what clutch to buy and throw out bearing. any input?

today i got my goetze head gasket and i copper sprayed it.

Untitled by clean3two3, on Flickr

Untitled by clean3two3, on Flickr
also washed my trans and replaced the shift linkage seat and replaced the front seal but forgot to add oil on the inside of the seal so it doesnt burn up so i ripped it out and i thought i had the rear trans seal just to find out i cant take the guibo hub out so i scrubbed it and poured steaming hot water on it and most of the dirt came off. looks better then what it was before.

Untitled by clean3two3, on Flickr
also took my motor to the shop to replace my front main seal.

Untitled by clean3two3, on Flickr
i wish i had air tools

Untitled by clean3two3, on Flickr

[efficient]

gonna bump this up.ive been lagging it on working on my car but i finally decided its time to work on it. :) im real happy that i pulled my very first engine by myself. kinda forgot to unhook the shifter and the clutch line so i just yanked it out. also did a little extra work on pulling the head just to see how the insides looked.
now i just need to assemble my m20b25 with a myster-e head.
20 years of dirt/grease. for sure gonna get cleaned real good before going back into the bay.

Untitled by clean3two3, on Flickr


Untitled by clean3two3, on Flickr


Untitled by clean3two3, on Flickr


Untitled by clean3two3, on Flickr
gonna have to clean the bay before putting the motor back in.

[efficient]

anyone know if i can just put new bearings on the crankshaft without doing anything to the crankshaft itself?
and
the pistons can i reuse the pistons but put new piston rings on them without honing the block?
any advice?

[e30m20TurbO7]

I Like how the car sits
i have a set of eibachs but yet to put them on interesting seeing the stance are your springs charcoal grey
and your on a good start all you need to do is rebuilt a seta bottom end or eta doesnt matter
find a intake, throttle body,injectors, ecu, wiring harness ,and more but good luck man
ironicly enough your first post for this thread was on my birthday

[efficient]

thanks. lol they are fake and one is bent. the wheels i have are these one's http://capetown.olx.co.za/15-borbet-...-iid-323517466 not really liking them. so anyone know why my valence is missing the upper line underneath the headlights? :( kinda sucks cus i cant return it anymore.

[Pantless Spency]

they do look pretty baller

[efficient]

so the alpinas are or arent yours?

nope could be.

[Pantless Spency]

so the alpinas are or arent yours?

[efficient]

Untitled by clean3two3, on Flickr

Untitled by clean3two3, on Flickr

so i tried putting on this bumper but its missing the piece underneath the headlights.

[efficient]

Was the car Bronzit at one point?

Looks like a good start!

it was bronzit at one point. So glad it isnt now. I never noticed it until a co worker said your car has been repainted. I bought the car without popping the hood because it wouldnt open. Little did I know you can use a screwdriver to open it from the front,also found out that the hood handle on the inside was loose so it wouldnt let me open it. Tightened it and the hood handle opens the hood.

[TimKninja]

Was the car Bronzit at one point?

Looks like a good start!