Idk how I just found this thread, but I love u.
Announcement
Collapse
No announcement yet.
Scum class 318 + Mtech + vortech v2 + unicorns - vortech + Turrrrbo
Collapse
X
-
Originally posted by pandaboo911 View PostHeaders are legal as long as the same o2 sensor location is retained..IG: @Baye30
FRONT VALENCE IS ZENDER!!! STOP FILLING MY PM BOX PPL!!!
Comment
-
Originally posted by golde30 View PostI never heard that before. I was always informed that the part had to be approved and issued a carbEO#. Did you retain the EGR and Evap systems for the OBD2 swap? I could never figure out how to retain the evap system from engine to fuel tank....
Take a look at KoKoSe7en's build thread, he passed BAR with headers, so I'm following the same path
The important part is o2 sensor is in same location, mounted at same angle, and the cats are approved for the vehicle. for '95 m3 walker 80801 is the approved cat
Evap they just do a visual on the charcoal canister and check that the gas cap seals.
Comment
-
Oh I assumed you were going for OBD2 because you said you have been looking for OBD2 pipes without success. I thought that was strange, obd2 midpipes are available all over, the OBD1 pipes are the hard ones to find. I have had my s52 OBD1 for years now, still haven't BARd it though.IG: @Baye30
FRONT VALENCE IS ZENDER!!! STOP FILLING MY PM BOX PPL!!!
Comment
-
Originally posted by golde30 View PostOh I assumed you were going for OBD2 because you said you have been looking for OBD2 pipes without success. I thought that was strange, obd2 midpipes are available all over, the OBD1 pipes are the hard ones to find. I have had my s52 OBD1 for years now, still haven't BARd it though.
I figured either way I was going to have to have my buddy weld it up so I just went all custom shiet
Comment
-
exhaust is done.. Sadly I couldn't fit the large magnaflow and had to use a 3" resonator instead. Still sounds awesome! Not pictured: H-pipe for the o2 sensor.
Using single 3" was a mistake. Although it sounds biblical, the ground clearance is an issue. Will definitely scrape under the subframe and over speedbumps. I just hope it doesn't rip off my shiny expensive new cats.
also installed my own CAI, this is not a kit.
Filter is completely isolated from the engine bay and sits behind the foglight duct. Beats any "heatshield" hot air intake
Note: The filter WILL be shielded from the tire when the fender liners are installed. Don't want the tire to kick up rocks or water and send them flying into the filter.
Comment
-
Very nice build. I was also thinking about going single 3" but the scraping was the problem. Where did you pick up your raceland headers for 140?sigpic
1989 325i Sold
2001 325i Sold
2005 Infiniti G35 Sold
1991 318is Rip
2005 Subaru Sti Sold
2009 Honda Civic SI Sold
2009 Honda Civic Si Sold
2003 Saab 9-5 Sold
1991 325ic MTech2 S52 Current
Comment
-
Originally posted by catalyst. View Postthe cai looks good, but be very careful driving in the rain you could hydrolock very easily
Comment
-
Mtech 1 beeld
Originally posted by gazil View PostVery nice build. I was also thinking about going single 3" but the scraping was the problem. Where did you pick up your raceland headers for 140?
I picked them up used. Someone bought them but never installed.
The mtech front has a bend underneath the bottom of the valance that should help shield the filter from the ground if I happen to drive through a puddle.
The car is running. Still working on installing my audio wiring before I finish up the interior.
Also have to hook up VSS to the ecu because it runs like shit while driving. I'm also having issues with my speedometer, it gets a signal while I rev the engine and goes crazy. The wiring manuals say the wires should be brown/red and brown/violet, but my wiring is brown/red and brown. Could it be interference screwing with the signal? I used a multimeter to check and it's the correct wiring for the speed sensor.
Also is the VSS a modified signal? Or is it a straight signal from the speed sensor?Last edited by pandaboo911; 01-25-2015, 10:45 PM.
Comment
-
How are you liking the brakes so far?1991 325i - "Scambles" The Daily Driven lightly modded.
1988 Mazda RX-7 TII "Mako" The Free Dorito
bacon by Jared Laabs, on Flickr
Comment
-
MT1 for 400.00? fuck you
nice build!~ Puch Cafe. ~ Do business? feedback ~ Check out my leather company ~
Instagram: @BWeissLeather
Current cars:
~ '87 325 M30B35 swap
~ '87 535
~ 01 540 Msport 6spd
~ '06 X5 4.8is
Comment
Comment