!!!!!Caution M20 porn inside!!!!!

[Jparkr]

Did you just "bump" your project thread?
update it to bump. Duh

[rs4pro3]

bump

[gstuning]

Nevermind then :)

[rs4pro3]

I'm running pure alpha-N, map sensor is just doing barometric correction.

[gstuning]

cool deal, I can do a setup when ever you are ready, I still want to get the lightweight flywheel and headers on my car anyways before getting it on the dyno

Are you still running a MAP sensor?

I was thinking that if you would put some foam inside the chamber all the TB´s connect to you might be able to soften the map signal at idle and low running,

Another thing you might want to check it is at what throttle angle your getting 100kpa,
it might be an idea to lenghthen the throw of the lever arm that moves the plates as to slow down the movement somewhat and thus the rise of pressure vs angle.

[Dyno4mance]

^^^ 2 Posts........he really wants those TB:pimp:
He said at the begining of the thread what they were...They are from a BMW motorcycle, so I would check craigs list or Ebay often

[tatertots]

this project is sick can you pm me where i can find the throttle bodies?

thanks man

[tatertots]

this project is sick can you pm me where i can find the throttle bodies?

thanks man

[dashboardmonkey]

That is some fuckin wild shit.
Looks good.

Andy

[rs4pro3]

cool deal, I can do a setup when ever you are ready, I still want to get the lightweight flywheel and headers on my car anyways before getting it on the dyno

[Dyno4mance]

Hey man long time, Ya I need to get it down there on the dyno, maybe sometime soon. Those are actually the GM coils I used. Do you have that 2.8 almost ready to go?

Not quite, bottom end is complete....81mm crank, 135mm Chromoly Eagle rods....etc,etc I am still working throught the cylinder head components
I think I may have to clay or "Tootsie Roll" the motor once the cam comes in as I have 11:1 compression pistons installed and I think I am going with a Schrick 288 Cam with MM beehive M5 springs...
As soon as money and time permitts I will be asking you to set me up with a Motronic boxed Mega squirt...:D
The chassis is finished complete with spec E30 cage so it is looking kinda race car ish
I thought you could maybe give me some wiring pointers while the dash and engine is out...are those coils from say a GM 3800 series II V6?
Call me when you need on the dyno and I will hook you up...

[Altstadthof]

subscribed! nice work!

[rs4pro3]

Hey man long time, Ya I need to get it down there on the dyno, maybe sometime soon. Those are actually the GM coils I used. Do you have that 2.8 almost ready to go?

When are you going to take up my offer to tune that thing on my dyno?
After all I am only down the road....
Of course it would not all be one sided as I do need some help with setting up my 2.8 on MS:D....That Bosch coilpack mod looks great, what are they from?
Joking aside....Give me a call if you need some free dyno time Ely
(706) 602 8881

[SpecM]

can I haz ITB m20?

that thing sounds so sick, congrats and nice work

[Dyno4mance]

bastard :finger:, nah I've got a 9lb aluminum flywheel sitting now in the garage ready to go on, so it's all good:D

When are you going to take up my offer to tune that thing on my dyno?
After all I am only down the road....
Of course it would not all be one sided as I do need some help with setting up my 2.8 on MS:D....That Bosch coilpack mod looks great, what are they from?
Joking aside....Give me a call if you need some free dyno time Ely
(706) 602 8881