Announcement

Collapse
No announcement yet.

PNW Chit Chat thread

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    dude i have an m50, this is not for my 318is motor
    Last edited by Matt-B; 03-03-2011, 05:53 PM.


    Please leave feedback below, thanks

    http://www.r3vlimited.com/board/showthread.php?t=358170

    Comment


      Originally posted by Matt-B View Post
      dude i have an m50
      dude is it in yet?

      Comment


        going to go ahead a say a week and a half...just got my last parts today


        Please leave feedback below, thanks

        http://www.r3vlimited.com/board/showthread.php?t=358170

        Comment


          Originally posted by Matt-B View Post
          going to go ahead a say a week and a half...just got my last parts today
          nice... just got my swap started today for the first time, amazing feeling. good luck with yours

          Comment


            Originally posted by Knoepfler View Post
            dude is it in yet?
            That's what she said....

            Comment


              Originally posted by Twelvizm View Post
              That's what she said....
              :rofl:
              Autobahn Motorsport - Portland, Oregon - restoration + service
              @autobahnmotorsport
              '88 M5 | '89 330is

              Comment


                Originally posted by Twelvizm View Post
                That's what he said....
                Fixed.
                '89 Schwarz E30 M3 Cabriolet Build

                Comment


                  So anyone wanna do a meet and help me do a center support bearing replacement? Mine is gettin pretty bad and it sounds like the driveline is smacking on the bottom of my car... I finally have a little bit of cash and it needs to be done... I dont have a garage to use due to the ix being down and I dont have air tools to make it a 20 minute job... I couldn't get it off when I did my guibo so I don't know what the deal is... I don't have the part yet but I will be ordering it tomorrow and also checkin with Kuni BMW. So who's up for it? I would love to check out the Horsepower freaks shop if that guy is down, but any help would be cool...
                  CBAKE
                  86 Eta (sold)
                  88 325ix (sold)
                  87 325i

                  Comment


                    Originally posted by cbake82 View Post
                    So anyone wanna do a meet and help me do a center support bearing replacement? Mine is gettin pretty bad and it sounds like the driveline is smacking on the bottom of my car... I finally have a little bit of cash and it needs to be done... I dont have a garage to use due to the ix being down and I dont have air tools to make it a 20 minute job... I couldn't get it off when I did my guibo so I don't know what the deal is... I don't have the part yet but I will be ordering it tomorrow and also checkin with Kuni BMW. So who's up for it? I would love to check out the if that guy is down, but any help would be cool...
                    you have to split the drive shaft and pre load that center support... kind of a pain.. order a febi one from pelican.. pretty cheap if i recall.

                    Comment


                      Snag one locally. I work at Kuni, so thats a good choice. :) CSBs are actually cake to do. Takes about 90 min on jack stands. 1/2 that on a lift with the right tools present. Separating the driveshaft and preloading the csb are the easiest part. Hardest is removing the four diff flange bolts, and pulling the bearing off. And those arent even hard.
                      sigpic

                      Comment


                        just take it to a driveshaft place its hella cheap
                        Originally posted by blunttech
                        r3v does not fuck around. First you get banned, then they shoot you

                        Comment


                          Matt, you sell that M42 yet?

                          Comment


                            yea why?


                            Please leave feedback below, thanks

                            http://www.r3vlimited.com/board/showthread.php?t=358170

                            Comment


                              Originally posted by Twelvizm View Post
                              Matt, you sell that M42 yet?
                              fail...

                              out dated sig is out dated

                              Comment


                                I had 2 for sale threads lol


                                Please leave feedback below, thanks

                                http://www.r3vlimited.com/board/showthread.php?t=358170

                                Comment

                                Working...
                                X