R3VLimited Forums

Go Back   R3VLimited Forums > Members List

nando nando is offline

Moderator

Visitor Messages

Showing Visitor Messages 1 to 10 of 23
  1. xXWarsmithXx
    11-09-2017 10:48 PM
    xXWarsmithXx
    Nando,

    Do you think that these could fit on a stock height, non-rolled/trimmed iX without rubbing/poking? I went through the entire wheel thread and I know that this offset is pushing it, but I would appreciate your thoughts on this matter.

    15"x7"et25, 4x100 (confirmed fit on basic e30) with a 205/55r15 tire.

    Respectfully,

    Caleb
  2. audiquattrot
  3. Blach178
    05-10-2017 03:02 PM
    Blach178
    okay ill look into it then. great that e30tech is back up ! thx for letting me know
    btw Ive asked you earlier about ignition maps ive stumbled upon your old 2*12x12 igniton map ! and copied it.


    is there any spots there need alittle less advance ?
  4. Blach178
    05-08-2017 01:42 PM
    Blach178
    Hey again Nando

    I havent been out driving that much because ive installed wasted spark and some other stuff. But now when im at it i want to install a cam sensor aswell. Ive bought at MRT plate with trigger mount to mount on the same spot of the dingy.
    Ive bought a M52 cam sensor.
    well now for my question.
    where to place the trigger degree wise?

    best regards
    Emil
  5. Blach178
    04-21-2017 10:33 AM
    Blach178
    cool thank you nando ! hope it works with prenium fuel :P
  6. Blach178
    04-21-2017 10:26 AM
    Blach178
    alright. so table 1 last collum 3533rpm. and table 2 fist collum 3767rpm ? just to be sure ?
    i dont wanna mess anything up :P
  7. Blach178
    04-21-2017 10:03 AM
    Blach178
    Cool ill try that out.
    just another question :P
    on your table the last colum #1 and first #2. where youve put 0000... is that to tell the ms to go on the second table ?
  8. Blach178
    04-21-2017 05:05 AM
    Blach178
    Hey Nando

    Ive been told its your website http://www.325ix.com/
    great website !
    I have installed a MegasquirtPNP from diyauto and started looking on good base ignition map. Ive looked at yours and thats 2x 16x16 and I only have the ability to go 2x 12X12.
    But well ive built a 2.8 m20 stroker 84x84 and with the 9.4:1 pistons.
    Can i scale down yours somehow to fit ?
    At the moment ive copied tinkerputzers timing map.

    hope you wanna help a newbie like me

    Emil
  9. bmw_fear
    04-27-2016 05:00 AM
    bmw_fear
    when you time have
  10. bmw_fear
    04-21-2016 05:21 AM
    bmw_fear
    I would be grateful if you could help me with more pictures and dimensions of the tube
    thank you anticipated

About Me

Statistics

Total Posts
Visitor Messages
General Information
  • Last Activity: Today 06:30 AM
  • Join Date: 11-29-2003
  • Referrals: 5

Friends

Showing Friends 1 to 6 of 6

All times are GMT -7. The time now is 02:14 PM.


Powered by vBulletin® Version 3.8.10
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Copyright 2004 - 2020 R3VLimited LLC