R3VLimited Forums

Go Back   R3VLimited Forums > Members List

Hellabad Hellabad is offline

E30 Modder

Visitor Messages

Showing Visitor Messages 1 to 9 of 9
  1. 6gen91
    11-21-2011 07:48 AM
    Your inbox is full, text me 773 983 0659 if your still interested..
  2. Pantless Spency
    08-10-2011 04:41 PM
    Pantless Spency
    Hey jay!
    I've swam in your pool before it was pretty fun lol!
    I also found a bearded dragon on your property the same day I believe
  3. IsItElectric?
    07-13-2009 03:49 PM
    Jay, my mobile is 610-470-3343. Give me a shout when you get a chance. Thanks.
  4. IsItElectric?
    07-13-2009 03:47 PM
    Jay, I called this afternoon and I spoke w/ Trevor, he said you weren't around. So I sent a couple pictures to his email address. Perhaps I can get you on the phone tomorrow? When is the best time to call?

    In any case, as I'm looking at it more, it's probably an issue with the hardware. Let's have a conversation about it?

    You guys have some great products and so far things are going great for me this season, on a GC suspension no less. So I am in no way trying to stir things up....just want to get this resolved!

    Thanks again,

  5. IsItElectric?
    07-13-2009 09:49 AM
    yeah just replied. Not trying to raise the red flag, just want to bring it to your attention.

    I will give you a call at some point. I talked to you on the phone before buying....not sure if you recall.


  6. Stephen
    06-04-2009 03:33 PM
    Where can i buy the shortened bilsteins? i dont see them on your site..

    And how much?
  7. dlmrun2002
    03-23-2009 09:54 AM
    Hey Jay.. Spoke to you last summer -fall. Have a full GC coilover suspension kit with Koni top adjustables front and rear. Also have camber plates(running-2.3).Like the kit a lot . Left side has been popping since day 1. Spoke to frankie(?).Did what he said-clean-lube white grease-anti-seize stuff.Thought I was missing a washer on the top hat bearing.Frankie sent me one. After looking at it a 2nd time, both washers were there. Bearing looks fine. Clean-lube-anti-seize a 2nd time. left side still pops on tight turns. I was curious to the top camber assembly. Under it it has a circlip holding the mount(in camber assembly) where the strut goes thru. I took circlip out to see if I could remove whatever it's holding in but no luck. Is that middle piece suppose to spin? I have the top strut guide from the kit and that is clean and lubed but I was wondering if something could be binding there. Thanks for your time.. Doug M NY 1991 318is GC kit
  8. Hellabad
    01-08-2009 03:27 PM
    I never even knew about this visitor message feature, I just clicked on something and your question showed up. The answer is yes.

  9. twistednut
    10-01-2008 05:37 PM
    I curious if your plates can adjust to where I am only running -.7 degrees camber. I am running Irelands now and I only have about an 1.25" inches of travel.

About Me

  • About Hellabad
    Nor Cal
    1987 325 is, euro bumpers
  • Signature
    Here is my photo gallery answering common questions about Ground Control Suspension, and e30 suspension problems in general.
    Ground Control Gallery

    The Ground Control facebook page: Dragged, kicking and screaming into social media to see what happens next.
    Ground Control facebook page


Total Posts
Visitor Messages
General Information
  • Last Activity: 05-29-2019 01:25 PM
  • Join Date: 08-20-2008
  • Referrals: 0

All times are GMT -7. The time now is 06:04 AM.

Powered by vBulletin® Version 3.8.10
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Copyright 2004 - 2020 R3VLimited LLC