R3VLimited Forums

Go Back   R3VLimited Forums > Members List

nando nando is online now


Visitor Messages

Showing Visitor Messages 1 to 10 of 24
  1. Bored
    11-17-2018 06:17 AM
    Hey Nando,

    New to the BMW-world, new to E30's and in fact have yet to pull the trigger on getting one.

    I've read through the topics concerning it but... what would it take to get an n52 in-and-running for a daily driver type car? Would you have a line on sourcing the parts?
  2. xXWarsmithXx
    11-09-2017 09:48 PM

    Do you think that these could fit on a stock height, non-rolled/trimmed iX without rubbing/poking? I went through the entire wheel thread and I know that this offset is pushing it, but I would appreciate your thoughts on this matter.

    15"x7"et25, 4x100 (confirmed fit on basic e30) with a 205/55r15 tire.


  3. audiquattrot
  4. Blach178
    05-10-2017 02:02 PM
    okay ill look into it then. great that e30tech is back up ! thx for letting me know
    btw Ive asked you earlier about ignition maps ive stumbled upon your old 2*12x12 igniton map ! and copied it.

    is there any spots there need alittle less advance ?
  5. Blach178
    05-08-2017 12:42 PM
    Hey again Nando

    I havent been out driving that much because ive installed wasted spark and some other stuff. But now when im at it i want to install a cam sensor aswell. Ive bought at MRT plate with trigger mount to mount on the same spot of the dingy.
    Ive bought a M52 cam sensor.
    well now for my question.
    where to place the trigger degree wise?

    best regards
  6. Blach178
    04-21-2017 09:33 AM
    cool thank you nando ! hope it works with prenium fuel :P
  7. Blach178
    04-21-2017 09:26 AM
    alright. so table 1 last collum 3533rpm. and table 2 fist collum 3767rpm ? just to be sure ?
    i dont wanna mess anything up :P
  8. Blach178
    04-21-2017 09:03 AM
    Cool ill try that out.
    just another question :P
    on your table the last colum #1 and first #2. where youve put 0000... is that to tell the ms to go on the second table ?
  9. Blach178
    04-21-2017 04:05 AM
    Hey Nando

    Ive been told its your website http://www.325ix.com/
    great website !
    I have installed a MegasquirtPNP from diyauto and started looking on good base ignition map. Ive looked at yours and thats 2x 16x16 and I only have the ability to go 2x 12X12.
    But well ive built a 2.8 m20 stroker 84x84 and with the 9.4:1 pistons.
    Can i scale down yours somehow to fit ?
    At the moment ive copied tinkerputzers timing map.

    hope you wanna help a newbie like me

  10. bmw_fear
    04-27-2016 04:00 AM
    when you time have

About Me


Total Posts
Visitor Messages
General Information
  • Last Activity: Today 07:35 PM
  • Current Activity: Viewing User Control Panel
  • Join Date: 11-29-2003
  • Referrals: 5


Showing Friends 1 to 10 of 10

All times are GMT -7. The time now is 07:36 PM.

Powered by vBulletin® Version 3.8.10
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Copyright 2004 - 2020 R3VLimited LLC