Announcement

Collapse
No announcement yet.

User Profile

Collapse

Profile Sidebar

Collapse
Avatar
tyeler18
Member
Last Activity: Yesterday, 09:16 PM
Joined: 07-01-2019
Location: Arizona
  •  
  • Filter
  • Time
  • Show
  • Source
Clear All
new posts

  • tyeler18
    replied to Imans LS1/T56 1987 325es
    I've driven plenty of manual brake setups. Same reason I don't run carbs on my cars. Power brakes work significantly better everywhere, multiple people drive my cars and I don't need anyone worrying about...
    See more | Go to post

    Leave a comment:


  • tyeler18
    replied to Imans LS1/T56 1987 325es
    I think you'll like the 3.73's. I too went from 4.10s down to 3.73s and it made 1st gear so much better to drive. I wouldn't even mind a 3.46 or similar just for highway driving but 80mph I'm barely over...
    See more | Go to post

    Leave a comment:


  • tyeler18
    replied to 1987 325es LS1/T56 swapped
    It seems that red is a popular LS donor chassis lol! Car looks good!
    See more | Go to post

    Leave a comment:


  • tyeler18
    replied to LSA swap
    He has a build thread on here. Pretty awesome setup, if I didn't have my hydroboost in the way mine would have an LSA already
    See more | Go to post

    Leave a comment:


  • tyeler18
    replied to LS1 swap 318IS
    I have 6 siberian huskies so it was just a matter of time before one of them ended up with something bad. Sucks that it's total blindness, but we're just dealing with it as it comes.

    The...
    See more | Go to post

    Leave a comment:


  • tyeler18
    replied to LS1 swap 318IS
    Race prep for the Dec. 11th event starts now. First on the list is suspension. Thanks to Northern posting about the civic coil sleeves on amazon. I was going to order AFCO collars/perches but for $50...
    See more | Go to post

    Leave a comment:


  • tyeler18
    replied to Northern's Cocaine Cowgirl
    Have you fit those amazon spring sets yet? I was going to order AFCO perches/collars but if those fit 51mm struts properly I'll just grab those and swift springs. I assume theyre 2.5" collars?
    See more | Go to post

    Leave a comment:


  • tyeler18
    replied to DIY Bluetooth Retrofit CM5908
    Once again thanks BBowman for the write up. I wanted to add to this for anyone wanting to simplify a little bit. I installed this module in my radio using this writeup and so far its been working flawlessly....
    See more | Go to post

    Leave a comment:


  • tyeler18
    replied to LS1 swap 318IS
    Small, but also large upgrade this weekend. The factory LS1 intake is one of/if not the worst flowing intakes of the gen 3/4 engines. The truck intakes are a better option for power in comparison. Our...
    See more | Go to post

    Leave a comment:


  • tyeler18
    replied to LS1 swap 318IS
    Yes, the rubber mounts just press down/hold the radiator snugly against the core support. I have the core support foam/rubber lined so it sucks it tight into the foam....
    See more | Go to post

    Leave a comment:


  • tyeler18
    replied to LS1 swap 318IS
    I just bent 2 aluminum L brackets and rivnut them to the bottom of the core support. With the radiator flush with the core support bar the upper factory radiator mount fits and holds it perfectly. Very...
    See more | Go to post

    Leave a comment:


  • tyeler18
    replied to LS1 swap 318IS
    Thank you again! I'm quite impressed how clear the sound is for being a 30 year old stereo



    It is quite the handful. I'll upload some of my track addict videos to show just how...
    See more | Go to post

    Leave a comment:

No activity results to display
Show More
Working...
X