Announcement

Collapse
No announcement yet.

M60B40 Heads on M62B44 Block

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    #16
    Talked to a friend of mine to pick his brain, showed him both heads and gaskets. Said putting smaller combustion chamber heads on bigger blocks is nothing new
    (honda guys have been doing this to get more hp) and will bump the compression ratio (need to measure and calculate ). 11 should still be fine on pump gas although may be worth looking into e85 .
    Last edited by Jean; 01-30-2012, 08:38 AM.
    Mtech1 v8 build thread - https://www.r3vlimited.com/board/sho...d.php?t=413205



    OEM v8 manual chip or dme - https://www.r3vlimited.com/board/sho....php?p=4938827

    Comment


      #17
      I think the M60 forum needs to buy Jean a christmas present next year for sharing all his research with us. Nice thread!

      Comment


        #18
        Haha no need, I just like to "overthink" things sometimes I guess to be 100% sure etc.

        Maybe this weekend I'll clean up the M62 head combustion chamber and fill both up with water and measure the difference :)
        Mtech1 v8 build thread - https://www.r3vlimited.com/board/sho...d.php?t=413205



        OEM v8 manual chip or dme - https://www.r3vlimited.com/board/sho....php?p=4938827

        Comment


          #19
          so..... Would it be relatively simple to build an OBD1 "M60B44" with an M62 block/crank/pistons, and M60B40 heads as well as M60B40 everything else?

          As in, take an M60B40, remove block/rotating assembly, replace w/ block/rot assy from M62?

          Could this be the new secret to making >300bhp NA motors for cheap??? Would the M60B40 ecu compensate for the differences?

          Starting to get a boner...

          Comment


            #20
            Originally posted by iamcreepingdeath View Post
            so..... Would it be relatively simple to build an OBD1 "M60B44" with an M62 block/crank/pistons, and M60B40 heads as well as M60B40 everything else?

            As in, take an M60B40, remove block/rotating assembly, replace w/ block/rot assy from M62?

            Could this be the new secret to making >300bhp NA motors for cheap??? Would the M60B40 ecu compensate for the differences?

            Starting to get a boner...
            Yup, mine's already built and sitting in my E30, awaiting the first fire up! Done and done... Except for the ECU... Mark D'Sylva will be doing mine, once I get him some baseline numbers...

            Garey


            Comment


              #21
              ^ exactly what Garey did :) I am just looking at the data since I didn't see any of it posted before.
              Mtech1 v8 build thread - https://www.r3vlimited.com/board/sho...d.php?t=413205



              OEM v8 manual chip or dme - https://www.r3vlimited.com/board/sho....php?p=4938827

              Comment


                #22
                ooo i like this thread...

                Comment


                  #23
                  Originally posted by bmwmech1 View Post
                  Yup, mine's already built and sitting in my E30, awaiting the first fire up! Done and done... Except for the ECU... Mark D'Sylva will be doing mine, once I get him some baseline numbers...

                  Garey
                  So you effectively have a 4.4L OBD1 M60??

                  keep us updated, I eagerly await!!!

                  Also another question: Are there valve diameter differences between the B40 and B44 heads?

                  Comment


                    #24
                    Originally posted by iamcreepingdeath View Post
                    So you effectively have a 4.4L OBD1 M60??

                    keep us updated, I eagerly await!!!

                    Also another question: Are there valve diameter differences between the B40 and B44 heads?
                    Yup, look at my build thread... there are pictures of the engine assembly. The valves are the same, the M60 has dual valve springs and slightly hotter cams, plus the dual row timing chain. Plus a 1 point boost in compression ratio, due to the smaller bore... should be peppy:D:D:D

                    Garey


                    Comment


                      #25
                      Originally posted by bmwmech1 View Post
                      Yup, look at my build thread... there are pictures of the engine assembly. The valves are the same, the M60 has dual valve springs and slightly hotter cams, plus the dual row timing chain. Plus a 1 point boost in compression ratio, due to the smaller bore... should be peppy:D:D:D

                      Garey

                      reading through it now...

                      Comment


                        #26
                        Originally posted by Jean View Post
                        Haha no need, I just like to "overthink" things sometimes I guess to be 100% sure etc.

                        Maybe this weekend I'll clean up the M62 head combustion chamber and fill both up with water and measure the difference :)
                        It's all that much talk until you throw down and have the chambers cc'd.
                        In addition to that, you'll need to take an accurate measurement of piston deck height and know head gasket thickenss.

                        Compression ratio is the ratio of (displaced volume + clearance volume)/(clearance volume)

                        Clearance volume consists of:

                        -piston deck volume (positive if piston is in the hole, negative if out of the hole)
                        -piston dome volume (negative if pop-up, positive if dish, zero if flat)
                        -head gasket volume (bore^2 * Pi * thickness of head gasket)
                        -chamber volume
                        -If you *really* want to get anal, include the crevice volume around the top ring land.

                        What are the bores in the two head gaskets?

                        Comment


                          #27
                          I am still eagerly awaiting some real world data and results. If this conversion DOES work, I would expect over 300 bhp.

                          Comment


                            #28
                            ^ you me and everyone else!

                            Come on spring!
                            Originally posted by ebelements
                            Also, for those who don't know, negative camber is the greatest thing since sliced bread(panera). Even tire wear is for city busses and the elderly.

                            Comment


                              #29
                              I remember someone stating that both the b40 and b44 have flat top pistons that reach the top of the block. Assuming that the head gaskets are the same thickness, it should be pretty close to 11:1 comp on the frankenstein.

                              Comment


                                #30
                                I have taken my b44 heads apart a few days ago and they are currently in the car, I need to drop them off to clean/test and then I'll attempt measuring both.
                                Last edited by Jean; 02-14-2012, 03:27 PM.
                                Mtech1 v8 build thread - https://www.r3vlimited.com/board/sho...d.php?t=413205



                                OEM v8 manual chip or dme - https://www.r3vlimited.com/board/sho....php?p=4938827

                                Comment

                                Working...
                                X