So I ordered new CV shafts from Napa. I needed to do this because
1. My CV boots are shot
2. There is a major clunking in the rear drivetrain with on/off throttle
3. complete new CV shafts from Napa w/ my discount are $67 a piece
and
4. I need my CV boots NOT to be ripped when I bring my car to the stealership for the free pre-race inspection for BMWCCA driving school on the 22nd.
So here is what happened.
I waited three days for Napa to get the parts from East JaBlip, went to pick them up, and the boxes were TORN hard-core in multiple areas. Looked like the Napa standard shipping method was a giant catapult. I looked through the tears, and yep, the CV shafts were in there, so I paid for them and feverishly drove home, hoping these shafts would solve the clunking problem, and getting more and more excited about driving school.
Got home, tore open one of the boxes (so to speak) and the inner CV joint was COMPLETELY APART. That's right, grease everywhere, six steel balls rolling around the box, cap somewhere close by, bearing ring dangling from the toothed CV shaft. Checked the other box, sure 'nuff, the boxes should have said "some extremely messy assembly required".
So I was a little irked, but so desperate was I to get these shafts in my car that I pain-stakingly re-assembled the inner CV joint, and much grease and cursing was had, and installed it in my pile-o-bolts E30.
So here is where the anguish begins. I went to assemble the other CV shaft, and TWO BALL BEARINGS WERE MISSING!!! This one only had 4 balls, kind of like Chuck Norris! (the other one was a full-blown James Hetfield with six balls of hardened steel.) Wow was I mad at this point, The two balls must have simply fallen out of one of the many holes in the box during its stratospheric trajectory from the adjacent hemisphere.
So My brain started thinking (uh-oh) and I decided to tear apart one of my old CV shafts for some balls. (Ok, keep the snide remarks to yourself...) Got a handful of steel balls, (I told you once...) and THEY WERE TOO BIG by like 0.0000001 mm!!!! I even used a hammer, yes, a hammer to try to get the bearing together! But to no avail.
So the situation remains thus: Because of some knot-headed maneuver in shipping and receiving, two teeny steel balls got lost, and thus my car will be on jack stands, AGAIN, for the next week, and I may very possibly miss the ONLY BMWCCA driving school this year because of this.
All I can say is Napa BETTER overnight me another CV axle, assembled this time, and not charge me a dime.
/end tirade.
1. My CV boots are shot
2. There is a major clunking in the rear drivetrain with on/off throttle
3. complete new CV shafts from Napa w/ my discount are $67 a piece
and
4. I need my CV boots NOT to be ripped when I bring my car to the stealership for the free pre-race inspection for BMWCCA driving school on the 22nd.
So here is what happened.
I waited three days for Napa to get the parts from East JaBlip, went to pick them up, and the boxes were TORN hard-core in multiple areas. Looked like the Napa standard shipping method was a giant catapult. I looked through the tears, and yep, the CV shafts were in there, so I paid for them and feverishly drove home, hoping these shafts would solve the clunking problem, and getting more and more excited about driving school.
Got home, tore open one of the boxes (so to speak) and the inner CV joint was COMPLETELY APART. That's right, grease everywhere, six steel balls rolling around the box, cap somewhere close by, bearing ring dangling from the toothed CV shaft. Checked the other box, sure 'nuff, the boxes should have said "some extremely messy assembly required".
So I was a little irked, but so desperate was I to get these shafts in my car that I pain-stakingly re-assembled the inner CV joint, and much grease and cursing was had, and installed it in my pile-o-bolts E30.
So here is where the anguish begins. I went to assemble the other CV shaft, and TWO BALL BEARINGS WERE MISSING!!! This one only had 4 balls, kind of like Chuck Norris! (the other one was a full-blown James Hetfield with six balls of hardened steel.) Wow was I mad at this point, The two balls must have simply fallen out of one of the many holes in the box during its stratospheric trajectory from the adjacent hemisphere.
So My brain started thinking (uh-oh) and I decided to tear apart one of my old CV shafts for some balls. (Ok, keep the snide remarks to yourself...) Got a handful of steel balls, (I told you once...) and THEY WERE TOO BIG by like 0.0000001 mm!!!! I even used a hammer, yes, a hammer to try to get the bearing together! But to no avail.
So the situation remains thus: Because of some knot-headed maneuver in shipping and receiving, two teeny steel balls got lost, and thus my car will be on jack stands, AGAIN, for the next week, and I may very possibly miss the ONLY BMWCCA driving school this year because of this.
All I can say is Napa BETTER overnight me another CV axle, assembled this time, and not charge me a dime.
/end tirade.
Comment