FS: Solid M20 Motor & Trans mounts.

[silence]

I was putting these in today and decided to try to do the motor and tranny mounts at the same time. Everything went go except the engine is to far forward, so non of the hole line up. It's about an 1 1/2" off. Any idea how I can get the engine/tranny back farther?

Is this in reference to an M50 swap? if so, what oil pan are you using?

[E30Savage]

Is this in reference to an M50 swap? if so, what oil pan are you using?

Its an regular M20, but i was able to get the engine to move using a racketing tie down strap. Now the mounts are in and ready to go.

[E30Savage]

Is this in reference to an M50 swap? if so, what oil pan are you using?

Its an regular M20, but i was able to get the engine to move using a racketing tie down strap. Now the mounts are in and ready to go.

[silence]

Its an regular M20, but i was able to get the engine to move using a racketing tie down strap. Now the mounts are in and ready to go.

Ok, glad you were able to work things out.

[Stephen]

Hows engine clearance/ height with these compared to stock? Presumably the same? Ideally would like to lift my motor slightly.

[Roysneon]

With the 24v mounts, dose the centered stud go on the subframe or through the mount arm?

[robgoesvroom]

Got them a couple weeks ago and I paired it with my akg shifter install, works great! Kinda bummed out that the new condor speed shops stickers came out after I ordered them though :p

Silence, do you see any problems with me running your trans mounts+oem rubber engine mounts on the street? I'm only planning on running the entire set when I go to the track, to help dampen the vibrations for normal driving conditions. They have been working fine for the past couple of weeks, no interference issues with my clutch fan hitting the radiator.

Good price, good product.

[silence]

Hows engine clearance/ height with these compared to stock? Presumably the same? Ideally would like to lift my motor slightly.

Stephen, the clearance for the m20 mounts is like stock. the swap mounts are based on stock height as well.
What is your reasoning for wanting to raise the motor?

With the 24v mounts, dose the centered stud go on the subframe or through the mount arm?

The centered stud should be on the subframe.

Got them a couple weeks ago and I paired it with my akg shifter install, works great! Kinda bummed out that the new condor speed shops stickers came out after I ordered them though :p

Silence, do you see any problems with me running your trans mounts+oem rubber engine mounts on the street? I'm only planning on running the entire set when I go to the track, to help dampen the vibrations for normal driving conditions. They have been working fine for the past couple of weeks, no interference issues with my clutch fan hitting the radiator.

Good price, good product.

ROBGOESVROOM, Shot me a $5 via paypal, and i'll send you some stickers in the mail. THat goes for anyone who wants 4 of the new 2"x2" Condor Speed Shop stickers.

Regarding the mounts, that combination may put a bit more stress on your trans brace, and trans case mounting points, due to the oem mounts up front allowing the engine to move from side to side, while the solid trans monts keep everything from moving... i'd suggest you upgrade to solid up front, or at least, 1 solid, 1 oem.

[StreetMafia21]

Ill take a set of the trans mounts for m20

[silence]

Ill take a set of the trans mounts for m20

Ok great, please send $30 via PayPal to silence8@aol.com

[FLG]

Will be sending some cash for stickers when I get home

Sent from my Galaxy Nexus using Tapatalk 2

[silence]

Will be sending some cash for stickers when I get home

Sent from my Galaxy Nexus using Tapatalk 2

sounds good

[StreetMafia21]

Ok great, please send $30 via PayPal to silence8@aol.com

payment sent :)

[FLG]

sent the monies for the stickers

[silence]

Thanks guys, i will ship tomorrow!