I'm going to part out my S50 and Trans out of my 95 M3 - I need room for my Engine swap!
PRICES ARE OBO I don't want to store this stuff! Lowball WILL be considered depending on how much of the stuff you take! If it says shipped that is shipped to the Cont. 48 States with insurance.
From what I can tell the block is most likely junk after MEGA $$$$$ put into it.
So what's good?
413 Redlable DME - SOLD!
E36 M3 Manual trans OBD I Harness uncut (Except for EWS green wire) and perfect - SOLD! - including injector plugs all intact
S50/M50 Intake - Sold one, have one more $100 Shipped - great for an OBDII car!
S50/M50 throttle body - SOLD
Injectors, fuel rail, and FPR - $80 Shipped
S50 MAF - $75 Shipped
M50 Head with S50 Valve train, which has been worked over by the fine guys at Memphis Motorwerks. They did a competition valve job, and did some mild port work. Needless to say this is a bolt on ready to go head that has had everything gone through already. (This head was being built with boost in mind) - This head was stupid expensive - $900.00 (NEW Vanos solenoid and timing hardware)
The same thing from VAC was well over 5,000.00
M3 Cams and trays - SOLD!
If someone wants the whole top end with everything listed above, I will do a package deal for $1000
S50 Short block - Rotating assembly is in great condition since rebuild. One piston should be replaced due to a nut that got into the motor. (The head that WAS on the car at the time is not the same head above) - $500 bucks for the whole thing - Remember the block may possibly be shot! New clutch and flywheel with less than 300 miles on it included.
Metal thermostat housing - $40
If someone wants EVERYTHING listed above I will take $1200.00
ZF 5 Speed Transmission - Shifts very well, low miles from what I can tell - $400 (new UUC hyd. line, slave cyl, and throwout bearing included) Will trade for an LS1 T56 that needs work.
'95 M3 Cats - SOLD!
If someone wants a full take the long block, trans, Clutch flywheel, accessories, and what ever other BMW motor partsI have I would take $1500.00
All prices are OBO and not including shipping unless specified.
Gotta make room for the new drive train!
I can get things truck shipped pretty reasonably through work, so the trans and short block can be shipped if needed.
I will trade for LSx goodies
All parts located in Walls, MS just outside of Memphis.
PRICES ARE OBO I don't want to store this stuff! Lowball WILL be considered depending on how much of the stuff you take! If it says shipped that is shipped to the Cont. 48 States with insurance.
From what I can tell the block is most likely junk after MEGA $$$$$ put into it.
So what's good?
413 Redlable DME - SOLD!
E36 M3 Manual trans OBD I Harness uncut (Except for EWS green wire) and perfect - SOLD! - including injector plugs all intact
S50/M50 Intake - Sold one, have one more $100 Shipped - great for an OBDII car!
S50/M50 throttle body - SOLD
Injectors, fuel rail, and FPR - $80 Shipped
S50 MAF - $75 Shipped
M50 Head with S50 Valve train, which has been worked over by the fine guys at Memphis Motorwerks. They did a competition valve job, and did some mild port work. Needless to say this is a bolt on ready to go head that has had everything gone through already. (This head was being built with boost in mind) - This head was stupid expensive - $900.00 (NEW Vanos solenoid and timing hardware)
The same thing from VAC was well over 5,000.00
M3 Cams and trays - SOLD!
If someone wants the whole top end with everything listed above, I will do a package deal for $1000
S50 Short block - Rotating assembly is in great condition since rebuild. One piston should be replaced due to a nut that got into the motor. (The head that WAS on the car at the time is not the same head above) - $500 bucks for the whole thing - Remember the block may possibly be shot! New clutch and flywheel with less than 300 miles on it included.
Metal thermostat housing - $40
If someone wants EVERYTHING listed above I will take $1200.00
ZF 5 Speed Transmission - Shifts very well, low miles from what I can tell - $400 (new UUC hyd. line, slave cyl, and throwout bearing included) Will trade for an LS1 T56 that needs work.
'95 M3 Cats - SOLD!
If someone wants a full take the long block, trans, Clutch flywheel, accessories, and what ever other BMW motor partsI have I would take $1500.00
All prices are OBO and not including shipping unless specified.
Gotta make room for the new drive train!
I can get things truck shipped pretty reasonably through work, so the trans and short block can be shipped if needed.
I will trade for LSx goodies
All parts located in Walls, MS just outside of Memphis.
Comment