SOLD: M20 with ~157k

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • arch4ngel
    Mod Crazy
    • Dec 2008
    • 791

    #1

    SOLD: M20 with ~157k

    SOLD!

    Pulling my m20 for an s52 swap.
    Car has about ~157k on it (need to double check that)

    Newish cam, according to po it was replaced at around 120k miles.
    Presumably head gasket was done at same time.

    Lots of maintenance done around 10k ago:
    Timing belt
    Ignition rotor, distributor cap cam seal and bav auto plug wires
    Oil pan gasket, rear main seal and pilot bearing
    ECU with 91 octane ebay chip (no information on it, came with car)
    Spark plugs (bosch copper iirc)
    Comes with new valve cover gasket

    Here's a startup video:


    Running the motor through 2nd and 3rd gear:


    Need to sell asap to clear out room in the garage.
    No shipping yet as I don't have the time or resources to do so currently.
    Motor is currently in the process of being removed, will be out of the car this week.

    EDIT: Motor is out of the car and taking up space in the garage. Need to get this out of here asap.

    I'd like $450 obo picked up. Make me an offer I can't refuse.
    Last edited by arch4ngel; 03-28-2013, 10:41 PM. Reason: Motor pulled
    Project
    Feedback
  • swooper
    Advanced Member
    • Jun 2007
    • 156

    #2
    Do you have compression numbers? Thanks

    Comment

    • arch4ngel
      Mod Crazy
      • Dec 2008
      • 791

      #3
      I'm in the midst of pulling the car apart and don't have a compression tester, but let me see what I can do.
      Project
      Feedback

      Comment

      • arch4ngel
        Mod Crazy
        • Dec 2008
        • 791

        #4
        Bump
        Project
        Feedback

        Comment

        • Dozyproductions
          R3V Elite
          • Jan 2007
          • 4682

          #5
          Originally posted by swooper
          Do you have compression numbers? Thanks
          x2

          Comment

          • arch4ngel
            Mod Crazy
            • Dec 2008
            • 791

            #6
            Just picked up a compression tester, will try and post numbers tomorrow.
            Project
            Feedback

            Comment

            • arch4ngel
              Mod Crazy
              • Dec 2008
              • 791

              #7
              Compression test results

              Cylinder 1


              Cylinder 2


              Cylinder 3


              Cylinder 4


              Cylinder 5


              Cylinder 6
              Project
              Feedback

              Comment

              • arch4ngel
                Mod Crazy
                • Dec 2008
                • 791

                #8
                Bump
                Project
                Feedback

                Comment

                • arch4ngel
                  Mod Crazy
                  • Dec 2008
                  • 791

                  #9
                  Bump
                  Project
                  Feedback

                  Comment

                  • arch4ngel
                    Mod Crazy
                    • Dec 2008
                    • 791

                    #10
                    Motors out, ready to load on a truck.

                    Project
                    Feedback

                    Comment

                    • canakami
                      Mod Crazy
                      • May 2010
                      • 743

                      #11
                      Comes with harness?
                      sigpic

                      Always chasin'

                      Comment

                      • arch4ngel
                        Mod Crazy
                        • Dec 2008
                        • 791

                        #12
                        Yup, harness and dme come with it.
                        Project
                        Feedback

                        Comment

                        • dadooish
                          Noobie
                          • Dec 2005
                          • 33

                          #13
                          Where in bay area? Any other mods done? Any leaks?

                          Comment

                          • arch4ngel
                            Mod Crazy
                            • Dec 2008
                            • 791

                            #14
                            In Emeryville/North Oakland area.
                            No mods done besides the lightweight flywheel chip and cai.

                            Leaks I'm not 100% sure about as it's sitting in a corner of my dark garage and hard to get a good look at the back side currently. But the head gasket looks clean all around and the oil pan has been replaced. The intake -> engine oil tube is leaking a bit but I'd replace all those gaskets and seals while I had the motor out anyway.

                            You're welcome to come check it out if you'd like, send me a pm and we'll go from there.
                            Project
                            Feedback

                            Comment

                            • arch4ngel
                              Mod Crazy
                              • Dec 2008
                              • 791

                              #15
                              Bump
                              Project
                              Feedback

                              Comment

                              Working...