Announcement

Collapse
No announcement yet.

1990 Sedan Parts

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    1990 Sedan Parts

    I have a large amount of parts off of a 1990 325i Sedan. I am stripping the chassis to race with so I don't need any of these parts. They are all in usable condition at a minimum. I can provide pictures for each part at request, I just didn't want to flood this thread with a ton of pictures. All prices are listed below and are "or best offer" and do not including shipping.

    SOME PICTURES CAN BE FOUND @ BMW Parts

    Door Parts
    door glass (lf) - $35
    door glass (lr) - $35
    quarter glass (lr) - $15
    door glass (rf) - $35
    door glass (rr) - $35
    quarter glass (rr) - $15
    window regulator w/motor (lf) - $40
    window regulator w/ Motor (lr) - $40
    window regulator - NO MOTOR (rr) - $20
    door lock actuator (lr) - $5
    door lock actuator (rf) - $5
    door lock actuator (rr) - $5
    interior door handle (left side 2x) - $10
    interior door handle (right side 1x) - $10
    exterior door handle (lr) - $10
    door harness (lf) - $10
    door harness (lr) - $10
    door harness (rf) - $10
    door harness (rr) - $10

    Electronics
    chime module - $5
    LF ABS Sensor - $10
    LR ABS Sensor - $10
    RR ABS Sensor - $10
    cigarette lighter - $5
    gas door lock actuator - $5
    trunk light and switch - $5

    Interior
    dash board - $100 (two small cracks (1in or less), 1 in a defrost vent, 1 in the passenger side well)
    rear seat belt set - $20
    armrest, door pull (rf) - $5
    armrest, door pull (rr) - $5
    armrest, door pull (lr) - $5
    b pillar cover (right) - $10
    b pillar cover (left) - $10
    grab handles (ceiling) 2x - $5 each
    brake pedal - $10
    clutch peal - $10
    clutch/brake rubber pads (2x) - $5 each

    Exterior/Misc
    jack - $20
    trunk black - $75
    right cowl vent - $5
    front passenger (right) side headlight bezel/grille - $20
    Bottle Cap Hub Caps (3x) - $5 each
    Last edited by curry; 11-05-2016, 12:30 PM.

    #2
    Do you have the stock antenna cable that runs from the radio to the antenna unit?

    Comment


      #3
      pm ed
      [ETA - E30 Adapters] 5 Lug kit with e46m3 front and e46 325/328i rear brake setup
      ---------------------------------------------------------------
      [ETA - E30 Adapters] - 5 Lug kit | DTM Shifter | DSSR
      ---------------------------------------------------------------
      Transaction Feedback

      Comment


        #4
        Pmd on cluster


        Sent from my iPhone using Tapatalk

        Comment


          #5
          what condition are the front and rear bumpers? And do you have the lower valance as well?

          Comment


            #6
            Originally posted by aaaaah View Post
            Do you have the stock antenna cable that runs from the radio to the antenna unit?
            I do have it in the car but I can probably pull it.

            Comment


              #7
              I'd be interested in it if it's not broken and you feel like pulling the cable

              Comment


                #8
                Originally posted by aaaaah View Post
                I'd be interested in it if it's not broken and you feel like pulling the cable
                I can pull it without too much trouble. The harnesses are coming out of the car anyway. Once I get it out, I will send pictures and a price.

                Comment


                  #9
                  Originally posted by 808vert View Post
                  what condition are the front and rear bumpers? And do you have the lower valance as well?
                  I have some local guys interested so they take precedence but if those fall through, I will let you know.

                  Comment


                    #10
                    Originally posted by curry View Post
                    I have some local guys interested so they take precedence but if those fall through, I will let you know.
                    Ok thanks

                    Comment


                      #11
                      Are you keeping the door edge gasket (body side "edge protector")? I'm looking for a driver's side that isn't shrunken at any corners.

                      Comment


                        #12
                        Originally posted by butters View Post
                        Are you keeping the door edge gasket (body side "edge protector")? I'm looking for a driver's side that isn't shrunken at any corners.
                        Not sure what you are looking for.

                        Comment


                          #13
                          Do you happen to have any mudguards?

                          Comment


                            #14
                            What color is the interior? Interested in both front door pockets, both rear speakers and the rf tweeter if intact.
                            Originally posted by LJ851
                            I programmed my oven to turn off when my pizza was done, should i start a build thread?

                            Feedback

                            Comment


                              #15
                              Originally posted by aaaaah View Post
                              I'd be interested in it if it's not broken and you feel like pulling the cable
                              Check your PM

                              Originally posted by Dzdimi14 View Post
                              Do you happen to have any mudguards?
                              Nope, sorry

                              Originally posted by chadthestampede View Post
                              What color is the interior? Interested in both front door pockets, both rear speakers and the rf tweeter if intact.
                              The interior is tan, see PM for pictures. Speakers are sold.

                              Comment

                              Working...
                              X