Enkei 2-piece wheels (similar to Weds Bavaria Fins)

[hexagone]

Helping a local forum member sell these wheels.

I don't have the exact specs *just* yet, but I figured I'd post them up to gauge interest and go from there.


Vintage Enkei 2 piece wheels (not sure if they're welded)

Look similar to Weds Bavaria Fins wheels

15x7

4x100

Low offset (10-20)

Do have curbage and bends, but certainly repairable.

$475 + shipping via Fedex. (expect $65 east coast, $75 west coast)

[kway]

PM'd

[hexagone]

The model actually "Enkei 94". Includes center caps.

Final specs are 15x7, et15 from what I'm told. No tires included. Offers considered.

[ivopivo]

Thanks a bunch Asim. These are my wheels that I have had no time to post up so Asim is helping out.

I will get photos up of each wheel to show exactly what's available.

To add to the above info... 3 wheels are perfectly straight but need some cleaning up. They don't have any bends, etc. just minor curbage as well as tons of crap all over as seen in the pics. They do clean up pretty well and if refinished would look perfect.

1 of the wheels hit a curb and the lip is bent about 1/2 of the diameter. It's bent back roughly 1/4" or so and while it's obviously out of balance, it held air for about 100 miles that I drove on it, highway and street, before I could get my spare with a decent tire on there.

As for size.. I don't know the exact sizes of the wheels as I really can't tell the offset from any of the markings, but from measuring, the wheel is 8" lip to lip (outermost points on each side of the wheel). Measuring from the inside lip to the part that mounts to the hub is roughly 4 5/8", ~117.5mm. So if center is 4", ~101.5, offset would be roughly +16mm.

That's all I got so far. If someone is interested in the tires they're Dunlop Graspic (3 are DS-1s with about 60% tread left and 1 is HS-1 with 80%+... PO replaced a blown DS-1 with this tire). I'll include them for cheap with the wheels... I used them through the winter but switching to 14" basketweaves.

Thanks again Asim.

EDIT: I told Asim +15mm because it looked like 4.5"-4 5/8" when I measured, so it's around 15-17mm I believe.

[kway]

Bump for moar pixs...

[Gadea]

Man, I´m loving those wheels. How easy of a fix is the one that is bent? Anyway most of my money is being drained towards my money pit....., I mean, swap...

[ivopivo]

Bump for moar pixs...

I didn't get a chance to take any lately but I'll find some time tomorrow after work. The rest of the wheels look exactly like the one pictured except they're straight with no bends at all... let me know if there are some specific pics you'd like to see.

Man, I´m loving those wheels. How easy of a fix is the one that is bent? Anyway most of my money is being drained towards my money pit....., I mean, swap...

I honestly don't know how easy of a fix it would be. A reputable shop here in the Chicago area told me it looks like an easy fix after seeing the pics (other pics of the bend as well not just the ones above), but I really can't say as I have no experience fixing bent wheels.

[ivopivo]

Here are a few I took with the cell phone. I will take some more photos tonight with an actual camera and post those up.

[ivopivo]

Some more pics from the cell phone... these are all on the car and not bent at all.

Driver Front:


Driver Rear:


Passenger Rear:

[ivopivo]

Last set of pics... All of the bent wheel that's off the car. The wheels aren't welded. Any special pic requests, let me know.

[hexagone]

tt

[hexagone]

up up up

[hexagone]

any offers

[ivopivo]

I'd really like to get rid of these as they're just taking up precious garage space.

Make me an offer I can't refuse and I'll more than likely bite.

[ivopivo]

Sold.