If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Made a few videos today when I took the cabrio to get smogged. They still really don't do the exhaust justice...the tone is so deep in the lower revs that the camera just can't pick it up. This is with a stock cat, btw.
Had some Focus guys talking to me about the car while it was on the dyno so didn't get any video of that. The wife drove it home so get a little video of that with her (good) camera. The other two were with my Storm2.
BTW in the final video I was so intent on stabilizing my blackberry that I hit the revlimiter in second and then didn't notice the cop coming towards me until I was halfway through 3rd. Oops. :) Good thing that wasn't in my wagon or it would have been ugly. 140kmh = 86mph.
I've been looking for pictures of ANY aftermarket muffler installed on diving board e30s but have come up short. Does anyone have any pics available for DB versions only? A Stromung muffler would obviously be best...
On that first link you can see if you need to replace any of your other parts, but everything else should be good, unless your rubber hangers are torn etc.
But, my question is that my automatic 86 325es has a great low millage oem cat on it so I would not want to touch it.
I am sure I will need an adapter to go from the single to this catback duel setup... but is this even worth doing or possible?
Also will I loose back pressure, well ha ha ha i have holes in the one now so i know I will gain back pressure but will it effect anything because I have an automatic?
Can they weld up an adapter for me?
I have a kid that rides in the car will it be too loud for like a sleeping baby?
And finally because I have a DB car will the exhause exit in the correct spot? (are all e30 exhaust locations identical?)
Thanks for your answers!
I'm sure any exhaust shop could make you an adapter to get it to work.
But, my question is that my automatic 86 325es has a great low millage oem cat on it so I would not want to touch it.
I am sure I will need an adapter to go from the single to this catback duel setup... but is this even worth doing or possible?
Since their is no resonator and it is duel will I loose back pressure, well ha ha ha i have holes in the one now so i know I will gain back pressure but will it effect anything because I have an automatic?
Can they weld up an adapter for me?
I have a kid that rides in the car will it be too loud for like a sleeping baby?
And finally because I have a DB car will the exhause exit in the correct spot? (are all e30 exhaust locations identical?)
Thanks, can you provide a list of parts needed, if say, i didnt have any to begin with? Im sure mine's going to need something since i'm replacing what is already a pretty rusted muffler.
On that first link you can see if you need to replace any of your other parts, but everything else should be good, unless your rubber hangers are torn etc.
I have had my Stromung for a couple years now and I love it. At idle it is pretty quiet, but it can put out the dbs. I love the sound though. There are a couple of tunnels in Seattle and I love shifting down and opening it up, sounds great. And it still looks great too.
One thing to keep in mind, this will last 2-3 times as long as a standard exhaust, so the price is not terrible.
Thank You Danny for fielding that last question. In regards to installation, you will simply remove the existing cat back and both lower hangers. The muffler will have provisions on it to simply bolt straight to the upper factory brackets.
The Cat back itself does not include any addition mounting hardware. If you need any new rubber hangers, mounting straps, or doughnut gaskets I would recommend calling your preferred parts house and ordering what you need ahead of time so that you have everything you need before installation.
In other news I have passed on the information on the 9 buyers we have already.
You should start receiving a call from Scott at Stromung for payment information.
All the materials have all ready been ordered for all 12 systems and we still have 4 open slots.
Production should be starting next week.
Take Care, and Thanks
Thanks, can you provide a list of parts needed, if say, i didnt have any to begin with? Im sure mine's going to need something since i'm replacing what is already a pretty rusted muffler.
Thank You Danny for fielding that last question. In regards to installation, you will simply remove the existing cat back and both lower hangers. The muffler will have provisions on it to simply bolt straight to the upper factory brackets.
The Cat back itself does not include any addition mounting hardware. If you need any new rubber hangers, mounting straps, or doughnut gaskets I would recommend calling your preferred parts house and ordering what you need ahead of time so that you have everything you need before installation.
In other news I have passed on the information on the 9 buyers we have already.
You should start receiving a call from Scott at Stromung for payment information.
All the materials have all ready been ordered for all 12 systems and we still have 4 open slots.
Leave a comment: