Who has dropped a trans (G260) out of a DOHC E30?

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • Wh33lhop
    replied
    Originally posted by jrdeamicis
    That insulation if left in makes it TOUGH to get some of the bolts.
    I didn't have much problem getting at the bolts. It was a bit of a bitch (had to use a wrench) but it didn't take that long. I wish I had known this when I was doing the swap though, I would have torn the fuck out of the insulation.

    Originally posted by triggrhaapi
    OR

    You have an engine hoist and you pull the motor out a little to tilt it, then it's a fucking snap.
    Why would I pull it up to tilt it when I can jack from the front of the oil pan to get the exact same effect?

    Originally posted by jrdeamicis
    There is MANY ways to do it.

    Lift the engine
    Remove insulation
    Magic Voodoo wand
    Jack the front of the motor up

    This guys in a parking lot on a public street. So I don't think the cherry picker is going to be the best option for him at the moment.
    Word. It would be epic doing that on the street but I'm going to avoid it if I can.

    Leave a comment:


  • Aptyp
    replied
    is insulation necessary for anything else outside of heat and noise? Because why not just take it off and have it off?

    Leave a comment:


  • jrdeamicis
    replied
    Originally posted by triggrhaapi
    OR

    You have an engine hoist and you pull the motor out a little to tilt it, then it's a fucking snap.
    There is MANY ways to do it.

    Lift the engine
    Remove insulation
    Magic Voodoo wand
    Jack the front of the motor up

    This guys in a parking lot on a public street. So I don't think the cherry picker is going to be the best option for him at the moment.

    Leave a comment:


  • triggrhaapi
    replied
    Originally posted by jrdeamicis
    That insulation if left in makes it TOUGH to get some of the bolts.
    OR

    You have an engine hoist and you pull the motor out a little to tilt it, then it's a fucking snap.

    Leave a comment:


  • rThor432
    replied
    Originally posted by jrdeamicis
    That insulation if left in makes it TOUGH to get some of the bolts.
    Especially with a ZF or 6-speed trans.

    Leave a comment:


  • jrdeamicis
    replied
    Originally posted by Wh33lhop
    Seriously, didn't even lower the subframe? I'll try it like this next time, if that doesn't work I'll try tilting it down like evangreen. Did you get rid of all the firewall insulation?
    That insulation if left in makes it TOUGH to get some of the bolts.

    Leave a comment:


  • rThor432
    replied
    Yeah man, no moving the subframe at all. I do not have the firewall insulation.

    Leave a comment:


  • Wh33lhop
    replied
    Originally posted by rThor432
    I removed the exhaust. Removed the driveshaft. Disconnected shift linkage. Supported trans with screw-Jack (floor Jack works on jackstands). Removed the trans crossmember and lowered the trans. Once it was tilted I hit all of the bolts around the bellhousing. If you don't have enough angle you can jack up gently on the oil pan with a block of wood between the jack and pan. Then I just pulled the transmission out. Sucks that it's being a bitch for you..
    Seriously, didn't even lower the subframe? I'll try it like this next time, if that doesn't work I'll try tilting it down like evangreen. Did you get rid of all the firewall insulation?

    Leave a comment:


  • rThor432
    replied
    Originally posted by Wh33lhop
    How'd you do it?
    I removed the exhaust. Removed the driveshaft. Disconnected shift linkage. Supported trans with screw-Jack (floor Jack works on jackstands). Removed the trans crossmember and lowered the trans. Once it was tilted I hit all of the bolts around the bellhousing. If you don't have enough angle you can jack up gently on the oil pan with a block of wood between the jack and pan. Then I just pulled the transmission out. Sucks that it's being a bitch for you..

    Leave a comment:


  • evangreen
    replied
    It cant really rotate that much until it hits. I left the jack supporting its weight though, when using the oil pan to support you want to spread out the weight as much as you can and use a softer material. Using wood works

    Leave a comment:


  • Wh33lhop
    replied
    I might just be able to rest the oil pan on the subframe and use the jack on the trans

    But then again, I'd think twice about supporting the engine by a piece of the oil pan :p

    I may get another floor jack, I just hate having huge tools that I will never use since I have nowhere to put them.

    Leave a comment:


  • evangreen
    replied
    Originally posted by Wh33lhop
    Sure I do. I live in a tiny apartment complex

    I got all the bolts off, and the trans is half off. But I'll give this a shot when I get the chance. Did you have to support the trans too to even out the load or did you just use 1 jack?
    I rotated my engine down when the trans was still attached, i still had that one bolt in. After i rotated it i let the trans just hang as low as it could. After taking the last bolt out i supported it in what i thought was the center with a cheapo floor jack and kind of wiggled it loose. then backed it out with the jack

    Get another cheapo floor jack, there inexpensive and light

    Leave a comment:


  • evangreen
    replied
    I swapped the engine out of my truck on a public street with a cherry picker last month, and that was in P.C. Berkeley.

    A cop came by and checked out what i was doing, he let me continue. He said that your not allowed to swap engines in the street, but if your car is inoperable your also allowed to do any work necessary to get it drivable.

    They would rather just let you finish than dealing with moving or towing a car thats half taken apart

    Leave a comment:


  • Wh33lhop
    replied
    Originally posted by evangreen
    Im doing this as we speak. I left the driver side motor mount connected, and unbolted the passenger side. Supporting the engine from the oil pan with some 2x4's on top of a cheapo floor jack ($15 at kragan with two jack stands, so now you don't have an excuse to not have one)
    Sure I do. I live in a tiny apartment complex with nowhere to work on my car, and I can't lug an 80lb jack 200 feet and down 2 flights of stairs every time I want to do anything, not to mention I don't have room for it anywhere in my apt. But I'll look into it. :p I've already got a Craftsman aluminum jack, that's enough to lug around.

    I lowered the engine rotating it.
    I had to do this to get to the top passenger side bolt, mine was too close to the fire wall to get a socket on. After this rotation I was able to snake it out
    I got all the bolts off, and the trans is half off. But I'll give this a shot when I get the chance. Did you have to support the trans too to even out the load or did you just use 1 jack?

    Leave a comment:


  • Wh33lhop
    replied
    Originally posted by Mr Two
    Of course you can. Go in from the front. The only other option is lowering it down via a jack, which wont be as safe.

    Dont skimp on it. Get the right tools, trust me.
    I also might mention that this is a public street, not a private parking lot. I kind of doubt the 5-0 is going to like someone with a cherry picker in the way of traffic, but I asked my friend to bring it up this weekend just in case.

    Leave a comment:

Working...