Who has dropped a trans (G260) out of a DOHC E30?

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • avery0829
    replied
    I'm in the process of doing this also, PM me if you have any questions.
    Btw I didn't use an engine hoist to do it.

    Leave a comment:


  • rThor432
    replied
    Originally posted by Wh33lhop
    Good to hear this is working for more people, that is plan A for next round.
    Trust me, it'll work fine and wont hurt your pan a bit unless you go crazy with it. When jacking up the front of the motor by the oil pan it will move freely until it starts to bind somewhere or torque hard against the motor mounts. That's when the pressure gets to a point that could potentially be detrimental to the oil pan, and of course you don't want to go any farther. You will feel it when it starts to get tough to jack it up. You will have plenty of room long before you run into a bind issue at the front end.

    I've done this for years and never once broken an oil pan. I wouldn't have even mentioned it or recommended it at all if there was even a decent chance of it busting the pan. I'd feel terrible if something happened as a result of my suggestion, but in this case you'll be fine.

    Leave a comment:


  • Jonny Cash
    replied
    Originally posted by Wh33lhop
    Ha. Easier said than done my friend. Plus, I've been sick for a day or two. Every time I go back out there I have to re-raise the car, put it on jackstands, drop the subframe, do my stuff, then before I leave, put the front end back together and lower it again for risk of it getting towed. So, instead of blindly prying and pulling with everything I've got and getting nowhere, I'm gathering some ideas to make it possible.
    Wonder if they'd start squeaking if you just put a car cover over it. Either way, you should have it out next time around.

    Leave a comment:


  • Wh33lhop
    replied
    Originally posted by 2002maniac
    Dont worry about it. Jack it up by the oil pan. Just use a block of wood to spread the load. This is what we did when we pulled the 260 from my brothers car after the swap (he forgot to install the pilot bearing!) Did not lower the subframe or anything...
    Good to hear this is working for more people, that is plan A for next round.

    Leave a comment:


  • 2002maniac
    replied
    Dont worry about it. Jack it up by the oil pan. Just use a block of wood to spread the load. This is what we did when we pulled the 260 from my brothers car after the swap (he forgot to install the pilot bearing!) Did not lower the subframe or anything...

    Leave a comment:


  • Wh33lhop
    replied
    Originally posted by Jonny Cash
    You want me to come over there, show you how its done? :P

    All the time you've spent posting, you couldve gotten it figured out already. Deep breath, grab it by the balls, and just rip it out.
    Ha. Easier said than done my friend. Plus, I've been sick for a day or two. Every time I go back out there I have to re-raise the car, put it on jackstands, drop the subframe, do my stuff, then before I leave, put the front end back together and lower it again for risk of it getting towed. So, instead of blindly prying and pulling with everything I've got and getting nowhere, I'm gathering some ideas to make it possible.

    Leave a comment:


  • Danny
    replied
    Bfh.

    Leave a comment:


  • Wh33lhop
    replied
    Originally posted by triggrhaapi
    You don't have a friend who can lend you some garage space for a few hours? Seriously? There are TONS of E30 guys in the SB area. I'm sure there is someone who can give you a proper work space. Hell, if you had posted a thread asking, you could have come to my house. I am more than willing to lend a hand.

    Making a habit of doing things the right way when it's a possibility is a good thing to do. Now when you HAVE to jerry rig something, it's not a bad skill to possess, but you shouldn't just do that to EVERYTHING.

    If your car wasn't already up on jackstands in some parking lot in SB, I'd say come to my house in the SFV and use my hoist.

    I wouldn't risk lifting the engine by the oil pan EVER. But that's just me.
    I'm 24 dude, my friends are in the same boat that I am. Even if they did have access to a garage, a) how am I going to get the car there with a AAA 7 mile tow, and b) am I really going to ask my friend to leave my torn-apart car in his garage or by his house for a week or two while I get the flywheel resurfaced, or to find a new bolt that I stripped? No. I'd rather take care of it myself, asking only for what I need. Call me self-reliant.

    And you can call it jerry-rigging, but as long as the end result is the same (new clutch and trans), who cares? Thanks for the offer, but Woodland hills is a good 75 miles away from me, which further illustrates my point.

    Leave a comment:


  • Jonny Cash
    replied
    You want me to come over there, show you how its done? :P

    All the time you've spent posting, you couldve gotten it figured out already. Deep breath, grab it by the balls, and just rip it out.

    Leave a comment:


  • triggrhaapi
    replied
    You don't have a friend who can lend you some garage space for a few hours? Seriously? There are TONS of E30 guys in the SB area. I'm sure there is someone who can give you a proper work space. Hell, if you had posted a thread asking, you could have come to my house. I am more than willing to lend a hand.

    Making a habit of doing things the right way when it's a possibility is a good thing to do. Now when you HAVE to jerry rig something, it's not a bad skill to possess, but you shouldn't just do that to EVERYTHING.

    If your car wasn't already up on jackstands in some parking lot in SB, I'd say come to my house in the SFV and use my hoist.

    I wouldn't risk lifting the engine by the oil pan EVER. But that's just me.

    Leave a comment:


  • Danny
    replied
    Why not just mandle it?

    Leave a comment:


  • Wh33lhop
    replied
    Originally posted by triggrhaapi
    Yes, and perhaps a parking lot on a public street is not the place to do this kind of work.
    Sure it is.

    Nothing he tries to do is going to be easy based on the limitation of where he has to do it. It's all going to be sketchy.
    Thanks for the help.

    Originally posted by triggrhaapi
    Well, because the oil pan is fragile and difficult to replace. Beyond that, a hoist will be bolted to the engine lift ring, which is designed to support the weight of the engine, as opposed to the oil pan which is not. Beyond that, you cannot securely lift the engine from the oil pan, so the potential result of that sad affair will be a broken oil pan and an engine on your face.
    Right, so what you're saying is, instead of applying pressure through some soft blocks of wood or particleboard to tilt the engine back (the oil pan can take at least 100lbs of force spread out, which should be more than enough to tilt the engine back), I should rent shop space, have my car towed there, bring the cherry picker to the shop just so I can use the hook to tilt the engine back.

    This is why I own a cherry picker and this is why I made sure that I got a place to rent that has a garage.
    Right, well I guess that's the difference between you and me. I'm a college student, I have to use what little money I have as effectively as possible. That means living close to school so I don't have to commute (lol at renting a place with a garage), I own a fun to drive $1200 car, and when shit breaks I fix it myself, wherever I can. The end result is I get to say I did an engine swap on my only car in a ranch 40 miles from where I live, a transmission swap in my parking lot, and I'm not afraid to work in less-than-ideal conditions.

    Leave a comment:


  • triggrhaapi
    replied
    Originally posted by Wh33lhop
    Why would I pull it up to tilt it when I can jack from the front of the oil pan to get the exact same effect?
    Well, because the oil pan is fragile and difficult to replace. Beyond that, a hoist will be bolted to the engine lift ring, which is designed to support the weight of the engine, as opposed to the oil pan which is not. Beyond that, you cannot securely lift the engine from the oil pan, so the potential result of that sad affair will be a broken oil pan and an engine on your face.

    This is why I own a cherry picker and this is why I made sure that I got a place to rent that has a garage.

    Leave a comment:


  • triggrhaapi
    replied
    Originally posted by jrdeamicis
    There is MANY ways to do it.

    Lift the engine
    Remove insulation
    Magic Voodoo wand
    Jack the front of the motor up

    This guys in a parking lot on a public street. So I don't think the cherry picker is going to be the best option for him at the moment.
    Yes, and perhaps a parking lot on a public street is not the place to do this kind of work. Nothing he tries to do is going to be easy based on the limitation of where he has to do it. It's all going to be sketchy.

    Leave a comment:


  • jrdeamicis
    replied
    Just unshim the motor
    Jack the front of the motor up (let the valve cover hit the firewall) [don't pinch any wires]
    Drop the subframe slightly. [Don't break the bolt]
    And try that.

    You could always use a pry bar and start making some space.

    Yeah, that insulation is a no go.

    Leave a comment:

Working...