Who has dropped a trans (G260) out of a DOHC E30?

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • evangreen
    replied
    Im doing this as we speak. I left the driver side motor mount connected, and unbolted the passenger side. Supporting the engine from the oil pan with some 2x4's on top of a cheapo floor jack ($15 at kragan with two jack stands, so now you don't have an excuse to not have one) I lowered the engine rotating it.
    I had to do this to get to the top passenger side bolt, mine was too close to the fire wall to get a socket on. After this rotation I was able to snake it out

    Leave a comment:


  • Wh33lhop
    replied
    Originally posted by jrdeamicis
    Take the motor off the arms( by supporting the motor from below) , drop the subframe. Lower everything. Remove the heatshields.

    Then raise the motor, bolt subframe.
    Support the motor with what? I've only got one jack, this is one of the problems.

    Also, why not just lower the motor and subframe as one?

    Originally posted by rThor432
    Weird, my G260 went in/came out like a stock one would. I had no issues at all installing/removing it when it was attached to the S52. I didnt loosen up motor mounts or lower subframes either. Good luck man.. hope it doesn't give you too much hell.
    Well, it probably has a lot to do with my shimmed motor mounts. But it just will not budge past a certain point, even after I dropped the subframe by almost 2 inches. I might want to try dropping the subframe on the longer subframe bolts again and jacking at the front of the oil pan tilting the whole assembly down... but I think last time I tried something similar the valve cover just got mushed into the firewall. How'd you do it?

    Leave a comment:


  • White325is
    replied
    ^^^ What he said. I have no issues either. But I dont have any of that inso fuckin with me either.

    Leave a comment:


  • rThor432
    replied
    Weird, my G260 went in/came out like a stock one would. I had no issues at all installing/removing it when it was attached to the S52. I didnt loosen up motor mounts or lower subframes either. Good luck man.. hope it doesn't give you too much hell.

    Leave a comment:


  • jrdeamicis
    replied
    Take the motor off the arms( by supporting the motor from below) , drop the subframe. Lower everything. Remove the heatshields.

    Then raise the motor, bolt subframe.

    Leave a comment:


  • Mr Two
    replied
    Of course you can. Go in from the front. The only other option is lowering it down via a jack, which wont be as safe.

    Dont skimp on it. Get the right tools, trust me.

    Leave a comment:


  • Wh33lhop
    replied
    I have one handy, but I can't really use it as there are cars to the left and right of my car.



    I don't think it's impossible without one, it's just been a bitch so far. I might be able to get away with pulling the hood or something and going in from the front (yeah yeah).

    Leave a comment:


  • triggrhaapi
    replied
    Originally posted by Wh33lhop
    I don't have a cherry picker at my disposal (working in a parking lot, and alone at that), so just lowering the drivetrain not connected to anything isn't very viable an option.
    Rent one. Can't be done without a cherry picker. That's why I kept the one I used to install the motor.

    Leave a comment:


  • Wh33lhop
    replied
    I don't have a cherry picker at my disposal (working in a parking lot, and alone at that), so just lowering the drivetrain not connected to anything isn't very viable an option.

    Leave a comment:


  • Mr Two
    replied
    Have you taken the motor mount arms off the motor, and lowered everything down and tilted it? I still haven't dropped the tranny in my car, but that's the way we did my buddy's S2k, and the clearances in that car are TIGHT.

    Leave a comment:


  • Wh33lhop
    started a topic Who has dropped a trans (G260) out of a DOHC E30?

    Who has dropped a trans (G260) out of a DOHC E30?

    How the FUCK do you get it all the way off? I tried getting long-ass subframe bolts and dropping the subframe down on that but it still wasn't low enough, some stupid tab on the trans was still pressing against the firewall no matter how I rotated it. I needed to drop the subframe another two inches at least (I've also shimmed the engine mounts, go figure). If I do this without bolts, it's going to be nigh impossible to get the subframe to line back up with the bolt holes thanks to a CAB that I didn't perfectly install.
Working...