*Power steering / crankcase vent questions*

[I*Do*Werke]

So are we saying that the m20 hose will fit the m52 and e36 rack?

I just looked on bmwfans and Im kicking myself for throwing away the m20 hoses...

[samiam3356]

Get them made up like he said. pretty sure BMW just went up on those hoses as well

[Adrian_Visser]

You will shit a brick when you see how much the e30 HP line costs. I suggest a trip to the pick and pull.

Some guys have gotten the e36 line modified by a hydraulics shop for less than the cost of the e30 line as well.

[samiam3356]

Wouldn't be too hard to fab something like that up if you wanted to use it.

[I*Do*Werke]

Oh and if anyone knows what power steering line to use, that would be greatly appreciated!

[I*Do*Werke]

I think it has to due with the car at idle. Throttle body open and it mainly vents to the boot. Closed it probable uses the smaller hose some. Not sure on this though.

I have thought about running an air/oil sperator like the OBD2 cars but I'm not getting a lot of blow by yet. I will worry about that latter.

I could use my cyclonic oil separator, but where would the oil drain to? The e34 dipstick does not have a fitting for the drain like the m52 dipstick does.

Also, have people run oil catch cans? That seems like an easy fix as well...

[samiam3356]

I think it has to due with the car at idle. Throttle body open and it mainly vents to the boot. Closed it probable uses the smaller hose some. Not sure on this though.

I have thought about running an air/oil sperator like the OBD2 cars but I'm not getting a lot of blow by yet. I will worry about that latter.

Something like this is what some of the guys on tech use that track their cars.

http://www.928gt.com/p-40363-provent-airoil-separator.aspx

[I*Do*Werke]

Cant speak on the powersteering because i dont have any currently. What I have done:

http://forums.bimmerforums.com/forum/showthread.php?t=602151

Item #9 on the conversion list. Basically because you have a plastic valve cover, you have to find a way to secure the obd1 oil seperator. I used a length of hose similar to the one used in the conversion thread I posted.

The tiny barb fitting attaches to a hose that goes to the connector for the ICV that mounts on the underside of the intake manifold. The larger fitting connects to the bottom of the intake boot. There should be two holes at the bottom of your intake boot (assuming you're using the obd1 throttle body and boot) the one closest to the MAF is for the ICV and the other one connects to the oil seperator.

Once you look at the oil separator, this will all make sense.

Thanks for your help.

So what you are saying is... On this diagram, I need to buy #1 and get a hose that will connect it to the obd2 valve cover. Then hose #3 goes to the intake boot and #4 is the barbed connector from the hose to the intake boot. Hose #5 goes to the connector on the bottom of the intake manifold where the ICV connects.

Crankcase-Ventilation - BMW parts catalog



What is the reason for the vacuum line that runs to the botttom of the intake manifold? The crankcase is under positive pressure and does not need vacuum.
What would be the benefit of running the setup listed above?
and what would be wrong with running a hose directly from the valve cover to the intake boot?

Thanks again :D

[sticksdaman]

Cant speak on the powersteering because i dont have any currently. What I have done:

http://forums.bimmerforums.com/forum/showthread.php?t=602151

Item #9 on the conversion list. Basically because you have a plastic valve cover, you have to find a way to secure the obd1 oil seperator. I used a length of hose similar to the one used in the conversion thread I posted.

The tiny barb fitting attaches to a hose that goes to the connector for the ICV that mounts on the underside of the intake manifold. The larger fitting connects to the bottom of the intake boot. There should be two holes at the bottom of your intake boot (assuming you're using the obd1 throttle body and boot) the one closest to the MAF is for the ICV and the other one connects to the oil seperator.

Once you look at the oil separator, this will all make sense.

[DTFE30]

What I did was use the original fitting that goes into the valve cover. I plugged the smaller line. For the Main breather line I put a 90 and then a breather filter from advance auto on. You can see it in the picture.. I don't think its ghetto.

[alpinescott]

I am about at the same point in my swap.....any ccv help, ie a diagram, would be great!

[I*Do*Werke]

Ive been working on my m52b28 swap for ~3 months now. Im at the last steps of the swap and Im getting stuck on a few problems...

First off, which high pressure power steering line should I use for a m52 / e36 steering rack combo? The line I need is from the rack to the ps pump. I have the e36 lines and there is no way they will work, and unfortunately, I do not have the m20 ps lines to see if they fit. Ive heard the stock e30 lines work, but I just want some clarification before I order them.

Second, What is the best way to connect the crankcase ventilation (ccv) to the intake? I have the obd2 valve cover. Can I just run a hose from the valve cover to the intake boot? Im worried about getting oil residue all over the throttle body and intake. I am a perfectionist and I do not want to ghetto rig it. Any help is greatly appreciated.