so i have a m50 vinos swap with 3.0 cams and over reved it today.. i have a hissing or maybe light scraping sound now and all compression is at 100 exept one by fire wall is at 60 .. what do i do and where to start??
-
-
Pull cyl head.
Check Us out on Facebook
Needing a harness adapter or wiring help? Check it out: also have 24v motor mounts, E30 M3 covers and E36 ECU mounts!
Full Product Line Tuning
OBD2 Tuning Available! OBD2 E36, S54 Swap, S62 Swap, etc: tuning@MarkertMotorWorks.com Dyno Thread -
also does any one know how the timing chain comes off.... master link??Comment
-
You should stop now.
Check Us out on Facebook
Needing a harness adapter or wiring help? Check it out: also have 24v motor mounts, E30 M3 covers and E36 ECU mounts!
Full Product Line Tuning
OBD2 Tuning Available! OBD2 E36, S54 Swap, S62 Swap, etc: tuning@MarkertMotorWorks.com Dyno ThreadComment
-
Bent valves would be my guess. No, there's not a master link on the timing chain. You need to pick up a Bently manual, maybe the '101 Performance Projects for you 3 Series BMW' book.‘Tis by the grace of God that my cars run!Originally posted by LJ851
Siobhan's Build Thread - UPDATED!Originally posted by unloadedak
Comment
-
The nice side of me says agree with this. The side of me that watches a lil kid stick a penny in a wall socket say KEEP GOING! Use a bicycle chain breaker LOLOriginally posted by 328ijunkie View Postsigpic"If one does not fail at times, then one has not challenged himself." -Ferdinand Porsche
The ugly car: http://www.r3vlimited.com/board/showthread.php?t=209713Comment
-
:stupid:
but take out the fucking tensioner its not that hard sounds like you shouldnt even have the car to begin with.84 318I Delphin RIP
87 325IS delphin 24v Sold
89 325 AlpineweissComment
-
jeez guys, give him a break, i looked for a master link the first time i played with one too... Its an honest thing to do...Comment
-
FixedOriginally posted by MattM View Post84 318I Delphin RIP
87 325IS delphin 24v Sold
89 325 AlpineweissComment
-
We are just pulling his chain LOLOriginally posted by MattM View Post
Ya I was terrible my first time too its kewlsigpic"If one does not fail at times, then one has not challenged himself." -Ferdinand Porsche
The ugly car: http://www.r3vlimited.com/board/showthread.php?t=209713Comment
-
How much did you over-rev it by?Originally posted by kbdrake07 View PostLeo.
E30 318iS, E36 328iComment
-
Some cars actually have a master link, so if I has worked on other cars besides BMW's I can understand why he would think that.
Get a Bentley for the E36 M3 and use that to pull your head. Also invest in the cam locking tool and the cam turning tool.Past Car : E30 S50 6 Speed 5 Lug 3.73
Current : Z3 S50 OBD2 (Smog Legal) 6 Speed BBS RN Dual Ear Diff
___________________________________________
BNB Designs
Engine Swaps, Fabrication, Innovation, General Repair
Richmond CA
Julian 848-248-8029
Comment
-
Good advice! That cam gear turning tool makes life much easier!Originally posted by jrdeamicis View Post‘Tis by the grace of God that my cars run!Originally posted by LJ851
Siobhan's Build Thread - UPDATED!Originally posted by unloadedak
Comment
-
The bentley e36 manual is available online in .PDF at Bf.c in the e36 section btw.
'89 Alpine S52 with goodiesComment
Comment