Great work! Imma have to do this when I 24valve swap! :up:
Looks a bit like a c5 corvette "bat wing" oil pan with the wide side things.
Another low profile S5x/M5x oil pan project! PICS!
Collapse
X
-
Well, I got around to installing it. Initial impressions are very good...as easy as the stock pan to install, no added pain there. The pan was a little warped but definitely not too much...no leaks. I installed with 'The Right Stuff' gasket maker; I have always used that stuff on pans since my Nissan days.
The on car fitment is great. My goal of making some other part of the car the lowest point was successful; the low point is now my steering rack. There is plenty of space on all sides of the pan. The three bolts on the passenger side forward edge are harder to get it, but there is plenty of room for a wrench still.
I had to switch back to the bolt-in windage tray and actually had some complications with that; my crank bolts were striking it on first start and sounded like some terrible bearing noise. I had to un-install my pan yet again and thankfully saw that the noise was only some light contact between my rod bolt heads and the new (used) windage tray....probably a little bent from the yard I got it from.
I will continue to update as time goes on. I am going to install an oil pressure gauge to see how it performs over all with some real data. Also, it holds the same volume as the stock pan; stock dipstick still works well but I obviously had to shorten the stick tube, the actual stick still works just fine ~1.5 inches.
Pics:
The last 'before' shot...this is how low the e34 pan sump hangs....keep in mind I have a deep front bumper with Mtech2.

Installed!

Here is a more zoomed-out shot:

New clearance...I know it's a little blurry, but you can make out the very leading edge of the new pan and see that the rack extends a little lower than the pan. I am probably squatting just a little lower than the first shot too because it is hard to see the new pan from the front!

More:


Thanks for the interest guys...I'd be happy to answer anyone's questions.Leave a comment:
-
Those look like Ramney's welds, haha. Semi local here, interested in the design.Leave a comment:
-
mod pan
With that much welding going on with any pan these need to be bolted down to a flat plate (gig) and go into production. Ya I need one too.Leave a comment:
-
Lmk if your pan weeps oil. Its seems that mine which is bizzarre because the guy that did is way to god damn good at welding.Leave a comment:
-
Thanks for the props, guys. I just got home from being at sea for a little bit, looking at finally putting it on in the next week or two!Leave a comment:
-
Very well done. In for pics of the pan installed!
Also, interested in a low-pro pan for my M20. ;DLeave a comment:
-
This is fantastic! Been following, anxious to see how it performs.Leave a comment:
-
the whole pan twisted. I put the pan on the block with no gasket it was warped about 1/16th or so. no real fitment problems. the oil pan gasket does leak just a little bit. not enough to drip on the floor though. just some seepage.Leave a comment:
-
Well, I wasn't thinking about making any other pans besides mine, but I might be able to get them done if we can get a batch going.
I will need to test fit mine to ensure success before further promising any delivery...can I get a tentative idea as to what you all would pay and who all is interested. Just an FYI, it cost me 200 on top of getting the pan to do it...
And just as an FYI, if I do make some, it will be a little on the slow side as this is not my main job and I am pretty busy with my day job usually.
To answer other questions in the thread:
kendogg, I haven't filled it up on the car yet, but with water, it got back to ~6, so unchanged but about 1.5 inches shorter.
!kid, Zeke; thanks for posting! Will check for weeps and also for fit. How much did yours warp and in what axis/direction? Did it result in a lot of fitment issues?Leave a comment:
-
Very cool. I would also be interested in a modded oil pan. Can't wait to see pics on the car.Leave a comment:
-

Leave a comment: