Mounting Euro Plate Filler - DIY? Walkthrough?

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • ACHTUNG
    replied
    Is there a way to mount the lic plate so it doesn't hang over at the bottom?

    Leave a comment:


  • dinanm3atl
    replied
    Pictures tomorrow...

    I put it on tonight :)

    Leave a comment:


  • dinanm3atl
    replied
    Well it is painted SEM trim. Drying now. Will mount tomorrow :)

    Leave a comment:


  • MR 325
    replied
    On my car [and trailer] I drilled out all four holes in the filler and removed the stock white plastic things. The plate and filler are bolted top and bottom with stainless steel bolts and lock nuts. Probably a bit excessive. :)

    Leave a comment:


  • dinanm3atl
    replied
    You will only use the top two mounting mounting holes and you will have to drill the plate filler. It will have an overhang.

    Leave a comment:


  • King Luis
    replied
    Originally posted by dinanm3atl
    Thanks to rwdrift

    Take out the stock white plastic bolt thingy's, line up euro plate filler. From inside the trunk, get a marker and draw holes on the back of the plate filler through the holes for the little white tabs you removed.

    Drill filler.

    Use nuts or some sort of rubber that'll hold the screws, tag and eventually the filler

    You got yourself an euro plate filler now


    I am going to do this and spray some undercoating on the isnide so no rust :)

    doesn't really answer my question.

    Leave a comment:


  • dinanm3atl
    replied
    Yah I saw that. That will be fine.

    Leave a comment:


  • M42Technik
    replied
    Originally posted by dinanm3atl
    That is what my idea was. But how to get it "perfect" :)
    Another OCD man in the house. What'll bother you is the US plate will hang a little off the bottom of the actual filler.

    Leave a comment:


  • dinanm3atl
    replied
    That is what my idea was. But how to get it "perfect" :)

    Leave a comment:


  • backtrail69
    replied
    I just drilled 4 7/8in holes in the filler where the white things are and slipped the filler in place and then put the plate back..

    Leave a comment:


  • dinanm3atl
    replied
    Originally posted by King Luis
    there is a how to some where on the forum..search plate and you'll see something.
    the only thing i need to figure out before i mount mine is do i cut my rear plate or is it supposed to mount a different way.
    Thanks to rwdrift

    Take out the stock white plastic bolt thingy's, line up euro plate filler. From inside the trunk, get a marker and draw holes on the back of the plate filler through the holes for the little white tabs you removed.

    Drill filler.

    Use nuts or some sort of rubber that'll hold the screws, tag and eventually the filler

    You got yourself an euro plate filler now


    I am going to do this and spray some undercoating on the isnide so no rust :)

    Leave a comment:


  • JJe30
    replied
    For mine (diving board bumper) I just matched up the plate and marked where the lic. plate mounts and drilled holes there and used the screws and mounted the plate.

    Leave a comment:


  • King Luis
    replied
    there is a how to some where on the forum..search plate and you'll see something.
    the only thing i need to figure out before i mount mine is do i cut my rear plate or is it supposed to mount a different way.

    Leave a comment:


  • dinanm3atl
    replied
    rofl thanks :)

    Makes it so I can have both my cars in my sig for all forums!

    Leave a comment:


  • Addissimo
    replied
    I have no clue, but your sig is sweet.

    Leave a comment:

Working...