Announcement
Collapse
No announcement yet.
Timing Belt / Water Pump DIY - Step by Step Pictures
Collapse
X
-
Can someone take pics of the marks? The only thing that scares me about this job is getting it placed right. The motor needs to be in TDC to complete the tb right? How do I ensure it stays in TDC?
-
nevermind problem solved! there's a little hole in the harmonic balancer offsetting all the other holes that tells you its exact position when you took it off, so you can put it back on correctly!
Leave a comment:
-
help! okay i took the harmonic balacer off without marking anything! how can i get it back on and aligned properly, im having a mini panic attack right now.... what do i do?
Leave a comment:
-
Originally posted by amcink View PostMy camshaft sprocket does not have the notch in order to align it with the TDC mark on the head.
I'm stuck since i also took out the crankshaft pulley and the lower timing belt cover so i cannot locate the TDC.
Should i just reinstalled everything and then try to find the TDC for the crankshaft and camshaft.
I also forgot to mention that i have not taken the sparkplugs out; therefore cannot turn the camshaft sprocket or crankshaft
Here it is the camshaft sprocket and camshaft area.
they cam sprocket and crank both have marks they are just super filthy!!!! Clean them up they are there. It is there on all cars your car is no exception.
On the cam sprocket you will see a 1/4 inch arrow on the inside and you will notice on eof the teeth is notched close to the head tdc mark.
the crank wheel same thing its there just not as deeply notched as an I........ just clean.....
Leave a comment:
-
Need major help i'm stuck
My camshaft sprocket does not have the notch in order to align it with the TDC mark on the head.
I'm stuck since i also took out the crankshaft pulley and the lower timing belt cover so i cannot locate the TDC.
Should i just reinstalled everything and then try to find the TDC for the crankshaft and camshaft.
I also forgot to mention that i have not taken the sparkplugs out; therefore cannot turn the camshaft sprocket or crankshaft
Here it is the camshaft sprocket and camshaft area.Last edited by amcink; 04-30-2012, 09:43 PM.
Leave a comment:
-
Why is this still not a sticky?! The OP went to the trouble not only to write it, but also to host all the pics for it somewhere that hasn't been cut off for maxing out the bandwidth restrictions.
Surely a post that's been up for 2+ years with this many hits and no broken images is deserving.
Leave a comment:
-
Originally posted by Tico Frank View PostIn the process of changing the belt I found out that the timing was off by 1 tooth so either the belt slipped from being so old or someone set it a tooth off. The car ran pretty good before but is alot smoother now. I'll post pics of how the timing was in the morning.
Edit: Just do the cam seal while you are at it. It took no more than an extra 15 minutes MAX and cost 2 bucks or so.
Do you have a part number on the cam seal? Thanks!
Leave a comment:
-
Yup use black RTV and lay a thin bead, then with a glove smooth it out
Leave a comment:
-
I just did all this and now I have a leak at the bottom of the water pump. Im assuming I have to pull it all apart again just to put some sealant on there?
Leave a comment:
-
In step 14 can someone highlight or circle the 3 bolts im suppose to loosen? I got confused and loosened the pulley bolts
Thanks
Leave a comment:
-
I did it fine, car started up perfect and bleed the coolant. I used other sites tho with more detailed info.
Leave a comment:
-
Originally posted by Thizzelle View Postthis diy needs a redo not as informative as it should be. No torque specs or anything about changing cam shaft seal which you would do as your there. Also no info about TDC this diy sucks and I'm sad because it's from r3v. Which is always the place to go. I had to use other sites :'(
This DIY does not cover the cam seal. People can choose to replace it or not. I didn't need to replace it, so I chose not to cover it in my write-up.
Step 29 refers to assuring proper alignment (you don't have to be at TDC, they just have to be aligned correctly) so maybe you didn't read that far...
Good luck with the project, sorry you didn't find my write-up adequate.
Leave a comment:
-
this diy needs a redo not as informative as it should be. No torque specs or anything about changing cam shaft seal which you would do as your there. Also no info about TDC this diy sucks and I'm sad because it's from r3v. Which is always the place to go. I had to use other sites :'(
Leave a comment:
-
Originally posted by Kommando View PostPretty much, you may not have to remove the hood, that makes it easier to access for the later steps.
Leave a comment:
Leave a comment: