Announcement

Collapse
No announcement yet.

Any interest in B35 mounts?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Jb325is
    replied
    I bought a set of these from Otis, ordered them on Saturday and got them today.. They're beefy! Thanks man!

    Leave a comment:


  • Good & Tight
    replied
    Just wanted to bump this up again, they are still available.

    Leave a comment:


  • Good & Tight
    replied
    Originally posted by SickE30 View Post
    So where does the BFH treatment take place? The whole fire wall? Or just around the brake booster?
    Just a small area were the back of the head would be, on the passenger side. It really doesn't need a BFH to get the job done.

    Leave a comment:


  • SickE30
    replied
    So where does the BFH treatment take place? The whole fire wall? Or just around the brake booster?

    Leave a comment:


  • Good & Tight
    replied
    Originally posted by SickE30 View Post
    So, if I am reading this correctly. Pos # 2 allows a/c and turbo fitment and requires very little BFH treatment? With Pos # 1 you can run turbo and no a/c? Or no turbo @ all and a/c with no BFH treatment @ all? Thanks Otis.
    Position #1 no a/c no BFH treatment, turbo yes.
    Position #2 allows a/c, needs BFH treatment, turbo yes.

    I am making another set tomorrow so it's ready to ship. :)

    Leave a comment:


  • SickE30
    replied
    So, if I am reading this correctly. Pos # 2 allows a/c and turbo fitment and requires very little BFH treatment? With Pos # 1 you can run turbo and no a/c? Or no turbo @ all and a/c with no BFH treatment @ all? Thanks Otis.

    Leave a comment:


  • Good & Tight
    replied
    Originally posted by Ali//325i View Post
    cool about to send paypal. What kind of paint did you use on the mounts? I am probably going to rustoleum them and paint them white so its easier to check for cracks down the road. Just didnt know if you already primed them or not.

    Money sent!

    -Ali
    It's high temp paint baked on. Got payment will ship out first thing next week and will send you the tracking #.

    Thanks
    Otis

    Leave a comment:


  • Ali//325i
    replied
    cool about to send paypal. What kind of paint did you use on the mounts? I am probably going to rustoleum them and paint them white so its easier to check for cracks down the road. Just didnt know if you already primed them or not.

    Money sent!

    -Ali

    Leave a comment:


  • Good & Tight
    replied
    Originally posted by Ali//325i View Post
    Sweet man. And just to clarify a couple of things, position 2 will allow turbo/air conditioning and needs sledge hammer action to fit the motor correct?

    Thanks for the close up!

    -Ali
    yes position 2 requires some hammer mods were the back of the head is. Just tap it in 1" below the brake line that's attached to the fire wall in a 8x8 area and that's it. A/C will work also.

    Otis

    Leave a comment:


  • Ali//325i
    replied
    Originally posted by Good & Tight View Post
    Here you go, they are ready to ship.

    Paypal---- Panayiotisx2@gmail.com

    Sweet man. And just to clarify a couple of things, position 2 will allow turbo/air conditioning and needs sledge hammer action to fit the motor correct?

    Thanks for the close up!

    -Ali

    Leave a comment:


  • Good & Tight
    replied
    Originally posted by Ali//325i View Post
    I'll prolly pick up that other set. Do you think you can get me some close ups of the welds and the joints. I trust that if you are using and another member they should be okay but I just want to make sure before I buy them :) Thanks!

    -Ali
    Here you go, they are ready to ship.

    Paypal---- Panayiotisx2@gmail.com

    Leave a comment:


  • Ali//325i
    replied
    I'll prolly pick up that other set. Do you think you can get me some close ups of the welds and the joints. I trust that if you are using and another member they should be okay but I just want to make sure before I buy them :) Thanks!

    -Ali

    Leave a comment:


  • Good & Tight
    replied
    Here is the oil pan clearance.
    Also have another set ready to ship.

    Leave a comment:


  • 884door
    replied
    Nasty welds. I can't believe anybody would pay $290 for these.

    Leave a comment:


  • Good & Tight
    replied
    Originally posted by learningcurve86 View Post
    just bought a set of these... I'll be sure to post a shot of them installed :)

    also- Jean: CA is one of those places I would visit but couldn't live. I would melt like an ice cube.
    Here are yours fresh out of the jig. Shipping them out tomorrow and will be in your hands by Wednesday.

    Thanks
    Otis

    Leave a comment:

Working...
X