Any interest in B35 mounts?

[Jb325is]

I bought a set of these from Otis, ordered them on Saturday and got them today.. They're beefy! Thanks man!

[Good & Tight]

Just wanted to bump this up again, they are still available.

[Good & Tight]

So where does the BFH treatment take place? The whole fire wall? Or just around the brake booster?

Just a small area were the back of the head would be, on the passenger side. It really doesn't need a BFH to get the job done.

[SickE30]

So where does the BFH treatment take place? The whole fire wall? Or just around the brake booster?

[Good & Tight]

So, if I am reading this correctly. Pos # 2 allows a/c and turbo fitment and requires very little BFH treatment? With Pos # 1 you can run turbo and no a/c? Or no turbo @ all and a/c with no BFH treatment @ all? Thanks Otis.

Position #1 no a/c no BFH treatment, turbo yes.
Position #2 allows a/c, needs BFH treatment, turbo yes.

I am making another set tomorrow so it's ready to ship. :)

[SickE30]

So, if I am reading this correctly. Pos # 2 allows a/c and turbo fitment and requires very little BFH treatment? With Pos # 1 you can run turbo and no a/c? Or no turbo @ all and a/c with no BFH treatment @ all? Thanks Otis.

[Good & Tight]

cool about to send paypal. What kind of paint did you use on the mounts? I am probably going to rustoleum them and paint them white so its easier to check for cracks down the road. Just didnt know if you already primed them or not.

Money sent!

-Ali

It's high temp paint baked on. Got payment will ship out first thing next week and will send you the tracking #.

Thanks
Otis

[Ali//325i]

cool about to send paypal. What kind of paint did you use on the mounts? I am probably going to rustoleum them and paint them white so its easier to check for cracks down the road. Just didnt know if you already primed them or not.

Money sent!

-Ali

[Good & Tight]

Sweet man. And just to clarify a couple of things, position 2 will allow turbo/air conditioning and needs sledge hammer action to fit the motor correct?

Thanks for the close up!

-Ali

yes position 2 requires some hammer mods were the back of the head is. Just tap it in 1" below the brake line that's attached to the fire wall in a 8x8 area and that's it. A/C will work also.

Otis

[Ali//325i]

Here you go, they are ready to ship.

Paypal---- Panayiotisx2@gmail.com

Sweet man. And just to clarify a couple of things, position 2 will allow turbo/air conditioning and needs sledge hammer action to fit the motor correct?

Thanks for the close up!

-Ali

[Good & Tight]

I'll prolly pick up that other set. Do you think you can get me some close ups of the welds and the joints. I trust that if you are using and another member they should be okay but I just want to make sure before I buy them :) Thanks!

-Ali

Here you go, they are ready to ship.

Paypal---- Panayiotisx2@gmail.com

[Ali//325i]

I'll prolly pick up that other set. Do you think you can get me some close ups of the welds and the joints. I trust that if you are using and another member they should be okay but I just want to make sure before I buy them :) Thanks!

-Ali

[Good & Tight]

Here is the oil pan clearance.
Also have another set ready to ship.

[884door]

Nasty welds. I can't believe anybody would pay $290 for these.

[Good & Tight]

just bought a set of these... I'll be sure to post a shot of them installed :)

also- Jean: CA is one of those places I would visit but couldn't live. I would melt like an ice cube.

Here are yours fresh out of the jig. Shipping them out tomorrow and will be in your hands by Wednesday.

Thanks
Otis