It's done just tuning now. Loses traction in third gear with drag radials.
Announcement
Collapse
No announcement yet.
M30 E30 official roll call thread
Collapse
This is a sticky topic.
X
X
-
Need a Turbo manifold? We have them in stock- Click here---> http://rapidspoolindustries.com/
____________________________
E-mail Panayiotisx2@gmail.com
Dyno vid http://www.youtube.com/watch?v=C7aM7..._order&list=UL
-
1986 325e
Mechanicals:
-m30b35 from a 1992 e32 735i
-g260/5(?) from a 1988 e28 535i
-Clutch and flywheel from an e34 M5
-e28 535i front half of driveshaft shortened 3/4 of an inch, factory 325e back half
-Joe Funk's engine mounts
-e30 325e transmission support
Electronics:
-e34 535i engine harness and computer
-e30 325e fusebox plug spliced on
-e30 325e coil
Exhaust:
-e32 735i manifolds and downpipe mated to the factory 325e exhaust
Cooling:
-e28 535i radiator
-e34 535i hoses; upper rad shortened 2", lower rad lengthened 2"; heater core hoses modified to fit
-e34 535i expansion tank mounted on firewall
Fueling:
-Ford Thunderbird 19# skinny injectors
Miscellaneous:
-e34 535i airbox
-e30 325ix washer fluid tank
Notes:
-No firewall modifications were needed with Joe's mounts. I did take the hood liner out, but this wasn't necessary.
-I had to cut 2 of the lower supports off of the radiator support in order for the e28 radiator to fit. I am currently using wire ties to hold the bottom, but I will be making some sort of mount to hold it more securely
-I had to enlarge the hole in the firewall where the ecu plug goes through.
-In order to fit the e32 downpipes, I had to cut some of the sound deadening off the firewall. I took the metal insulator pieces off the downpipes as well, but they might fit with them still on
-I converted to an 1995 e36 M3 steering rack while I had the engine out, there were no clearance problems at all
-In order to fit the e34 overflow tank, I had to cut the lower support off the bottom of the tank and remove all of the harness cover studs on the firewall. Hood modification was also required.
-I am using a m42 coolant temp sensor with no problems
So far I have only driven it about 50 miles. I am having fuel pump problems than I haven't been able to diagnose.
I'll update this with pics and sound clips once I get it running again.Last edited by E30SPDFRK; 11-16-2008, 10:23 PM.Byron
Leichtbau
Comment
-
1990 E30 316 bare shell in lach silver
1990 E32 M30B35 (from an auto)
E30.de engine mounts (position III)
E34 gearbox
Nice new late E30 sport e spoke leather steering wheel
Z3 shortshift
IR front and rear sway bars (25mm/22mm)
IR poly bushes set (street setting)
IR upper front strut bar
IR rear upper strut bar
shortened transmission
5 Lug conversion
Z3M front Hugger and calipers
Z3M front shocks and coils
Z3M rear shocks
E36 Compact rear suspension
BBS 17"/8" RK (SOLD)
Buquet seats
Mocal oilcooler
750i brake master cilinder
Two side windows (shadowline)
radiator and fan
E36 318Ti calipers
Z3 steering rack
Rear Bumper
E30 M3 2.5 EVO Alloy control arms
E30 M3 offset polly bushes
differential 3.45 open diff
E30 M3 black headlights
Rear discs
Z3M rear springs
still need:
325ix servo pump
Rear seats
xenon conversion
IS lipp
M3 Front Discs
Tyres
WILLWOOD FRONT AND BRAKE CALIPERS ON THE WAY!!!!
Comment
-
LowR3V'in - image doesn't work. What driveshaft and coolant components did you end up using?Mtech1 v8 build thread - https://www.r3vlimited.com/board/sho...d.php?t=413205
OEM v8 manual chip or dme - https://www.r3vlimited.com/board/sho....php?p=4938827
Comment
-
woops.
^Stock e30 driveshaft
E34 coolant lines.
stock 325i overflow.
Location: USA
Engine:M30B35 (e34)
Trans/clutch: e28 single mass/Clutch kit.
G260/6
Shift linkage:stock m20 e30 (had to use the m20 gear selector)
Drive shaft: stock m20 e30
Diff: 2.93lsd
Motor Mounts: Home made
Last edited by LowR3V'in; 03-12-2013, 07:07 PM.
Comment
-
84' 318i
e30.de mounts in pos III
m30b35 from a e32 91' 735i
e28 535i radiator
auto wiring harness from the e32
e32 auto ECU ends with "150"
g240 tranny from the m10
stock m10 flywheel
215mm spec stage 3 clutch (six puck 290lb tq capacity)
85' 325e driveshaft
2.93 LSD from some e30.... cant remember what model. (plan on changing it.. but I want to see how it does with the NOS)
Ebay chip
50 wet shot of nitrous, then bump to a 75.
Runs like a bitch!! I mean bitchin!! Bad ass. 0-80 in no time. 1st 2nd 80mph haha. long gears :)Last edited by flawdaboi407; 10-26-2009, 08:36 AM.84' 318i m30b35 swapped!
Comment
-
1991 325i
Location: San Antonio, TX
M30B35 from 89 735i
e28 535i flywheel
Getrag 260 transmission
Shift linkage, unsure, came out of parts bin.
driveshaft: e30 rear, e28 front
2.93LSD - only thing they had at the yard
Funkmasta motor mounts
e24 headers and downpipes
3" single exhaust back to a dynomax muffler
need a short shifter, won't go into reverse.
Comment
-
i forgot to join the club....
90 e34 m30
e34 5spd
funk mounts
jimc chip
ie radiator
ie poly motor/tranny mounts
e28/e30 driveshaft
3.73lsd
ie st3 springs
koni adjustables
gc rsm
ie sways
akg bushings (entire rear subframe)
ss lines
ate slotted rotors
hawk hps pads
r3v thread
at the harris hill track this weekend
current state...
Last edited by xlr8rbob; 05-24-2009, 09:33 PM.sigpic
www.strictlyea.com
Comment
Comment