Announcement

Collapse
No announcement yet.

Getrag 250 questions...

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Getrag 250 questions...

    I'm swapping m50nv with its Getrag 250 out of 1992 525i into my 325i... can I use m20 G260 single mass flywheel and clutch on G250? I've searched and could not find anything specific.
    Also which driveshaft should I use... I'm assuming e34 shaft won't work. I have 1987 325is manual driveshaft... will it fit?
    Thanks
    "i love vee tek, its a wonderful sound when you driving right by it"

    If you bought anything from me, please leave a feedback here: http://www.r3vlimited.com/board/show...ghlight=drulle

    #2
    not that much help... but what about throw out bearing? can I use stock g250 or the one from m20 bearing?
    "i love vee tek, its a wonderful sound when you driving right by it"

    If you bought anything from me, please leave a feedback here: http://www.r3vlimited.com/board/show...ghlight=drulle

    Comment


      #3
      idk if it helps but when i did my M50 swap i have an m50v with a Getrag 250 and a m20 lighten fly wheel with a e36 drive shaft.The guy that helped me do it said i needed a e36 325is or a e30 325is drive shaft cause i have a 318i.

      Comment


        #4
        Originally posted by 4doorE30=D View Post
        idk if it helps but when i did my M50 swap i have an m50v with a Getrag 250 and a m20 lighten fly wheel with a e36 drive shaft.The guy that helped me do it said i needed a e36 325is or a e30 325is drive shaft cause i have a 318i.
        Thanks a lot for this info, but do you remember by any chance which throw out bearing did you use?
        "i love vee tek, its a wonderful sound when you driving right by it"

        If you bought anything from me, please leave a feedback here: http://www.r3vlimited.com/board/show...ghlight=drulle

        Comment


          #5
          Im in the same boat.. Going getrag 250, bought the drive shaft that goes with it out of a 318i. No idea about throw out bearing, or clutch slave or anything. Hope we can figure this out!

          Comment


            #6
            Originally posted by Ecrossdaily View Post
            Im in the same boat.. Going getrag 250, bought the drive shaft that goes with it out of a 318i. No idea about throw out bearing, or clutch slave or anything. Hope we can figure this out!
            I ended up using 323i throw out bearing (BavAuto was cheapest) and G250 clutch slave (tranny came with it in my case)... all works perfect.
            "i love vee tek, its a wonderful sound when you driving right by it"

            If you bought anything from me, please leave a feedback here: http://www.r3vlimited.com/board/show...ghlight=drulle

            Comment


              #7
              Perfect, thanks man!

              Comment


                #8
                What pilot bearing do you use for the g250 with m20 flywheel and pressure plate?

                Also what is the part number for the 323 throw out bearing? Bav auto lists the 323 and 325 being the same:

                Comment


                  #9
                  I used m50 / G250 pilot bearing
                  Can't find the receipt with part #... sorry
                  "i love vee tek, its a wonderful sound when you driving right by it"

                  If you bought anything from me, please leave a feedback here: http://www.r3vlimited.com/board/show...ghlight=drulle

                  Comment


                    #10
                    Originally posted by drulle View Post
                    I used m50 / G250 pilot bearing
                    Can't find the receipt with part #... sorry
                    Damnit, looking to start my swap next week - this looks like it's going to stall the process.

                    Comment


                      #11
                      I have seen Part # here on R3V... just search for it. Good luck with your swap, it was really fun and interesting project for me. Important part is to have lots of patience and have all the pieces you need on hand.
                      "i love vee tek, its a wonderful sound when you driving right by it"

                      If you bought anything from me, please leave a feedback here: http://www.r3vlimited.com/board/show...ghlight=drulle

                      Comment


                        #12
                        which shifter linkage and driveshafts are you getrag 250 dudes using?

                        Comment


                          #13
                          I used late e30 325i manual driveshaft
                          had to shorten both aluminum and metal linkages, both e30
                          "i love vee tek, its a wonderful sound when you driving right by it"

                          If you bought anything from me, please leave a feedback here: http://www.r3vlimited.com/board/show...ghlight=drulle

                          Comment

                          Working...
                          X