Ideal SSK for E30? Not looking for big reduction
Collapse
X
-
Glad it worked out. Yeah man, if I remember correctly all it took was removing two C clips and the thing comes out. I had to remove mine about 3 times before i ground down enough material off. Fun times.Yeah its a pretty nasty sound. I got a cheap dremel from Lowe's earlier today and shaved the darn thing. I was mistaking the selector rod with the shift arm. Shift arm was a bitch to remove (clip on to of tranny), but selector rod took 5 minutes to remove. All went better than expected.Leave a comment:
-
I run a Z4 3.0 shifter. It will give you a much shorter shift than stock. In the case of the 318iS, no bending or grinding is needed.

After about 12 months, the setup was feeling a little sloppy again (I replaced all bushings and stuff with the shifter). So I got some AKG Delrin shifter arm bushings and it made the shifting MUCH cleaner (perhaps a little notchy). FYI, you will probably want to hit the Bitch Clip pin with a wire wheel and lube that, the top of the tranny where the bushings slide between and maybe sand the ends of the bushings a little. They are a TIGHT fit, and sort of a pain in the ass to get the Bitch Clip pin into with the tranny under the car. That was my experience anyway!Leave a comment:
-
Gonna piggy back on this thread...but, I plan on going with an AKG one because I love how tall it is. My question is: why is it recommended for race use only?Leave a comment:
-
Yeah its a pretty nasty sound. I got a cheap dremel from Lowe's earlier today and shaved the darn thing. I was mistaking the selector rod with the shift arm. Shift arm was a bitch to remove (clip on to of tranny), but selector rod took 5 minutes to remove. All went better than expected.
The Z3 shifter does feels better than stock. :thumbsup:Leave a comment:
-
Just put the z3 in with all new stock bushings. Very pleased with it. I took the balancer off and bent nothingLeave a comment:
-
Hah thats how I found out about it too. You just gotta take the selector rod out, and grind down the point thats hitting. The good thing about driving on it like you did, is that now you have what you need to grind down marked.Leave a comment:
-
Wish I read this sooner. I just finished putting everything back together, and i can hear the driveshaft balance banging against the selector rod. Its amplified at 2nd and 4th and faint with all other gears.I have a Z4 2.5 on mine and love it. I can't really give you a percentage, but the throw is def shorter than stock, and a bit notchy. The height of the physical shifter is much shorter too. If you have the harmonic balancer still on, you will need to grind the selector rod a bit. I hear no modification is necessary if your car has no balancer (mine did). In the pic it is shifted in second gear.

...so what the hell do I do now.
Leave a comment:
-
I like E46 330i OEM Lever. No reason to have a ridiculously stubby lever and notchy feeling z3/4 when you can have the same shift movement with a 3 series unit.
Since you have a e46 with a short shift linkage unit installed, Why not just install the lever lying around your garage into your E30?
I think $0 is the amount I paid for mine and the 330 replaced a Z3 lever in my E30; I was happier. If desired a BMW performance sport shift knob for E90 would be a perfect way to lower the top length; it can be ordered from your local dealer with a 5 speed pattern if you have a 5 speed in your E30.Leave a comment:
-
-
There's really nothing wrong with a cheap short shifter. I'd say it's only worth it to either get a different OEM lever for super cheap, or go all out and get AKG that bolts to the transmission tunnel. But I've felt an AKG shifter and in my opinion it's not worth the price tag. Maybe for a track car, but the difference is so minor that a good lever and delrin bushings in the front and rear will be almost indiscernible from an AKG.Leave a comment:
-
I have a z4 3.0 and love it. As do most people that drive my car. It has a very short throw & it sits fairly low.Leave a comment:
-
Out of topic, but your e30's interior is incredible!@
I have a Z4 2.5 on mine and love it. I can't really give you a percentage, but the throw is def shorter than stock, and a bit notchy. The height of the physical shifter is much shorter too. If you have the harmonic balancer still on, you will need to grind the selector rod a bit. I hear no modification is necessary if your car has no balancer (mine did). In the pic it is shifted in second gear.

Leave a comment:
-
Thanks for all the recommendations guys. While comparing it on the link provided above, looks like z4 levers give a huge reduction. E30 M3 shifter has a hefty price tag. $250 on ecs! I looked up the pricing for a new 1.9 z3 shifter, and I think this will do. :up:Leave a comment:

Leave a comment: