Cost of a Auto to Manual Swap
Collapse
X
-
I have an 88 that came from the factory with metal bumpers. Obviously, it can accept plastics without modification.
Also came w/ late tails -- so I'm going to call it.. a late model?Leave a comment:
-
Leave a comment:
-
thanks for the tips. do you know if an 88 is considered a late model?Others here will know a lot more than me - search and read in the transmission forum.
But I think any trans will work. IF you had an early eta with crank position sensors on the bell housing, you'd need that transmission and flywheel with trigger pins. If a later car, the sensors are on the front cover so they used a different flywheel.
The single-mass and dual-mass flywheels have a different depth, so you have to buy the correct throwout bearing for that bell housing and flywheel.
I believe all manual driveshafts are the same. Get a new center support bearing / carrier and rubber guibo to match your output flange. Don't take the driveshaft apart without marking the two halves - it is factory balanced.Leave a comment:
-
Others here will know a lot more than me - search and read in the transmission forum.
But I think any trans will work. IF you had an early eta with crank position sensors on the bell housing, you'd need that transmission and flywheel with trigger pins. If a later car, the sensors are on the front cover so they used a different flywheel.
The single-mass and dual-mass flywheels have a different depth, so you have to buy the correct throwout bearing for that bell housing and flywheel.
I believe all manual driveshafts are the same. Get a new center support bearing / carrier and rubber guibo to match your output flange. Don't take the driveshaft apart without marking the two halves - it is factory balanced.Leave a comment:
-
If I have an 88 (unsure if this is considered early anymore) -- super eta which came with an optional LSD -- would it matter if my trans was from early vs. late?Well-documented subject here on r3v.
But here is my recent experience -
160k early transmission, shifter, crossmember, driveshaft $500.
Used single mass flywheel $100
Pedal box assembly $80
Then all the new parts you need (some OEM, not all) can add up to $500. Price them all at someplace like Pelican Parts or Blunttech.
So the whole thing is $1000.
Much better to get all you can used in one package - piecemeal will add up fast. But you'll want a new clutch and PP, new master and slave cylinder, new mounts, new seals, new guibo, etc etc.
Early-late is based on your needs and your car...eta, seta, i, & flywheel type - which affects which throw-out bearing you'll need.
Also, which driveshaft should I use?Leave a comment:
-
Well-documented subject here on r3v.
But here is my recent experience -
160k early transmission, shifter, crossmember, driveshaft $500.
Used single mass flywheel $100
Pedal box assembly $80
Then all the new parts you need (some OEM, not all) can add up to $500. Price them all at someplace like Pelican Parts or Blunttech.
So the whole thing is $1000.
Much better to get all you can used in one package - piecemeal will add up fast. But you'll want a new clutch and PP, new master and slave cylinder, new mounts, new seals, new guibo, etc etc.
Early-late is based on your needs and your car...eta, seta, i, & flywheel type - which affects which throw-out bearing you'll need.Leave a comment:
-
I too am looking for info on the swap. I'll just post here instead of creating a new thread (hope you don't mind).
- Are there any considerations re: early vs. late cars?
- Is it cheaper to source parts individually? Or buy a complete swap?
- What is the average price per part if bought individually?Leave a comment:
-
Normally a 5spd manual swap taken off of a car will run you 700-900. If you have no idea what condition of the clutch/pressure plate are I'd recommend replacing them. Should do the master and slave while you're at as well.
Are you looking for a shop to perform this in your area or are you tackling this yourself?Leave a comment:
-
Cost of a Auto to Manual Swap
Hey I'm looking into doing a manual swap. I not sure how much a manual swap will cost. I'm assuming somewhere from 400-1000$. Which parts will be the most expensive? How much is a good condition G260 tranny?
Parts:
transmission
trans cross member
trans mounted exhaust hanger
clutch disk, pressure plate, throwout bearing w/fork and spring, pivot pin
flywheel
driveshaft w/ CSB and guibo and hardware
shifter assembly including bracket that bolts to body at the back of the assembly, the boot, and the sound deadening shit below it
master and slave cylinder, hoses, hard lines with body clip for trans tunnel
pedal boxTags: None

Leave a comment: