E30/M60 remove 530 5spd after install ?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • 36brua
    Mod Crazy
    • Feb 2008
    • 689

    #1

    E30/M60 remove 530 5spd after install ?

    Can the trans be removed /installed from under the car after installed in E30 / M60 ? Looks to me to be just as fast to pull eng/trans.
    TIA
    My CA legal M60 swap

    The happening in our garage
  • Chris916
    Advanced Member
    • Nov 2010
    • 183

    #2
    Nope. I tried a few weeks ago to swap clutch/flywheel, and the bellhousing gets jammed up on the tranny tunnel. It won't back out enough to clear the input shaft out of the flywheel splines so you can't drop it down. I spent 4 hours banging and prying to end up giving up and pulling the engine... which took 45 min.

    Comment

    • 36brua
      Mod Crazy
      • Feb 2008
      • 689

      #3
      Thanks ^^ I just pulled engine thanks for the confirmation
      My CA legal M60 swap

      The happening in our garage

      Comment

      • Yorl
        Advanced Member
        • Mar 2012
        • 172

        #4
        Yup, mine same thing. And the longtubes make it even worse....

        Comment

        • 36brua
          Mod Crazy
          • Feb 2008
          • 689

          #5
          Originally posted by Yorl
          Yup, mine same thing. And the longtubes make it even worse....
          Thank for the confirmation on that. why did you pull the trans? After seeing your post about the TTV flywheel we decided to use it. We are having trouble getting the clutch to fully engage, did you run in to this issue as well? and what clutch did you pair with the TTV flywheel?

          thanks again!
          My CA legal M60 swap

          The happening in our garage

          Comment

          • Yorl
            Advanced Member
            • Mar 2012
            • 172

            #6
            I dropped the engine in first to do the wiring harness, and when I got the clutch, I tried to install it without removing the engine.... I failed.
            I just started the engine today, so I'll get back to you tomorrow on the clutch situation ;)

            Comment

            • Jean
              Moderator
              • Aug 2006
              • 18228

              #7
              How is the clutch situation with the TTV flywheel?
              Mtech1 v8 build thread - https://www.r3vlimited.com/board/sho...d.php?t=413205



              OEM v8 manual chip or dme - https://www.r3vlimited.com/board/sho....php?p=4938827

              Comment

              • dasmanschaft012
                Mod Crazy
                • Apr 2014
                • 642

                #8
                Originally posted by Jean
                How is the clutch situation with the TTV flywheel?
                I have a 5sp, I am using the TTV flywheel and a southbend stage 2 S52 clutch.
                It fit fine, but haven't finished the car yet so not sure if it works or not yet.
                We're in deep now boys
                1988 325i SETA - Daily driver
                1988 340iL - Track car
                My M60 V8 swap thread here
                [oo==OO==oo]

                Comment

                • 36brua
                  Mod Crazy
                  • Feb 2008
                  • 689

                  #9
                  5spd set up
                  TTV flywheel
                  Clutchmasters e36 m3 stage 1 clutch and pressure plate
                  My CA legal M60 swap

                  The happening in our garage

                  Comment

                  • wakdog
                    Wrencher
                    • Mar 2011
                    • 223

                    #10
                    TTV flywheel and 5spd with Spec stage 3 M52 clutch, works perfectly.

                    90 318i M62B44 OBD1
                    02 530i Touring (Airlift 3P)

                    Comment

                    • Jean
                      Moderator
                      • Aug 2006
                      • 18228

                      #11
                      Originally posted by wakdog
                      TTV flywheel and 5spd with Spec stage 3 M52 clutch, works perfectly.

                      https://www.youtube.com/watch?v=lMv-px6r5wY
                      Nice!
                      Mtech1 v8 build thread - https://www.r3vlimited.com/board/sho...d.php?t=413205



                      OEM v8 manual chip or dme - https://www.r3vlimited.com/board/sho....php?p=4938827

                      Comment

                      • dougie30
                        E30 Mastermind
                        • Apr 2012
                        • 1708

                        #12
                        Originally posted by 36brua
                        5spd set up
                        TTV flywheel
                        Clutchmasters e36 m3 stage 1 clutch and pressure plate
                        i have this exact setup and drove it for the first time for about 10-15 miles, feels great.:up:

                        edit- i lied it isnt a clutch masters pp it is the fx one from ebay, still feels good.
                        M30 is God's motor.....but Jesus drives an M60'd car -slammin.e28

                        Comment

                        Working...