How to connect an oil cooler, M60

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • dirty30
    replied
    No, just no. Leave it stock and save yourself the headaches like Justin said!!

    Leave a comment:


  • Mykk540i/6
    replied
    I had wanted to do an oil cooler and remote spin on set up on my build. Bummer there's so many problems with them, considering stock filter housing now

    Leave a comment:


  • dasmanschaft012
    replied
    Originally posted by JGood

    Either way, that is all WELL within the operating range of the parts I was using.
    Most spin on filters have internal pressure relief vales, seems strange that you guys keep blowing stuff up.
    I will be sticking to the stock system (adapted to AN-10) and ill see how track time goes.

    High-key really dissapointed i may not be able to use this baller Setrab i have...

    Leave a comment:


  • JGood
    replied
    Originally posted by dasmanschaft012
    On track tho? I'm worried about cooling.
    What oil pressures do you guys see?

    20psi at idle, jumps up to 70psi by 2k, ~80psi above 4k. Seems high, but it was like that with my m60 and my m62. The pump pressure relief is supposed is 60psi IIRC, not sure if the spring is weak or what.

    Either way, that is all WELL within the operating range of the parts I was using.

    Why not try to run it, monitor oil temps, and work on cooling if needed? No reason to fix stuff that isn’t broken, and risk stuffing a car into a wall when shitty aftermarket parts fail.

    YMMV, just a very stern warning to be careful. Obviously these parts should all work fine, an engine is an engine and oil is oil, but so far we’ve seen bad results, and until an explanation is found, I’d say it’s an ongoing risk. I’d hate to see someone else do what I did and ball up a car, or worse yet, get hurt. Catastrophic oil loss on a track generally means spins and/or fires.

    Leave a comment:


  • dasmanschaft012
    replied
    Originally posted by JGood
    The factory stuff works 100% perfectly.
    On track tho? I'm worried about cooling.
    What oil pressures do you guys see?

    Leave a comment:


  • JGood
    replied
    Originally posted by dasmanschaft012
    I'm about to switch to a spin on adapter. should i be worried :(((((
    i also have a cooler im plumbing in (Setrab)
    Both Ryan and I tried using the spin on filter adapters. My first adapter leaked from the middle of the casting as soon as I fired the car up. After replacing it, I got pin holes in every single oil filter I installed. Ryan did as well. I built an enclosure around mine to eliminate the potential from external impacts. No difference, so it was happening from the inside out. My best guess was cavitation, but I really don't know. Then Ryan and I both went through 3-4 various oil coolers, all would randomly explode, leaving the car sitting on the side of the road, luckily not blowing up the engine as we both ran oil pressure gauges and caught it in time each time.

    I'll never use an aftermarket oil cooler/filter setup on a street car again. The factory stuff works 100% perfectly. It almost cost me my car/life when it hit my brakes at highway speed.

    Leave a comment:


  • dasmanschaft012
    replied
    Originally posted by JGood
    Save yourself some time and money, just go buy a few gallons of oil and dump it all over your engine bay and underside of the car. Same result as installing an oil cooler on an m60 e30.

    I have no idea why they constantly blow oil coolers (and standard spin-on filters, if you decide to make two bad decisions in a row, by converting to that as well). I gave up prior to figuring it out. The last straw was when a filter blew, covering my passenger front brake disc in oil, causing me to do a 360 on the highway when I hit the brakes, missing my buddies e39 M5 by a few feet, and somehow not flip as I slid through mud sideways.
    I'm about to switch to a spin on adapter. should i be worried :(((((
    i also have a cooler im plumbing in (Setrab)

    Leave a comment:


  • JGood
    replied
    Save yourself some time and money, just go buy a few gallons of oil and dump it all over your engine bay and underside of the car. Same result as installing an oil cooler on an m60 e30.

    I have no idea why they constantly blow oil coolers (and standard spin-on filters, if you decide to make two bad decisions in a row, by converting to that as well). I gave up prior to figuring it out. The last straw was when a filter blew, covering my passenger front brake disc in oil, causing me to do a 360 on the highway when I hit the brakes, missing my buddies e39 M5 by a few feet, and somehow not flip as I slid through mud sideways.

    Leave a comment:


  • jpod999
    replied
    JGood has nothing but issues with aftermarket oil coolers. Eventually just got rid of them.

    Leave a comment:


  • obetten
    replied
    both aftermarket. on of them was rated 500psi. edit: yes, i blew up two of them

    Leave a comment:


  • jpod999
    replied
    Aftermarket or oem M20 cooler?

    Leave a comment:


  • obetten
    replied
    I connected the oilcooler after the oil filter. Reason: Hot oil flows better trough the filter. But the cooler blew up and i dont understand why?

    Leave a comment:


  • The Dark Side of Will
    replied
    Originally posted by obetten
    So you would say that the cooler should be between the outlet of the pump and filter?
    Right. Oil should go from the pump to the cooler to the filter and into the engine.

    Leave a comment:


  • dasmanschaft012
    replied
    Originally posted by The Dark Side of Will
    Counterpoint:

    The last thing the oil should go through before it goes to your bearings should be the filter.
    I take my opinion back I like this more. TBH, either is probably ok but this sounds like a more desirable feature.

    Leave a comment:


  • obetten
    replied
    Originally posted by The Dark Side of Will
    Counterpoint:

    The last thing the oil should go through before it goes to your bearings should be the filter.
    So you would say that the cooler should be between the outlet of the pump and filter?

    Leave a comment:

Working...