Diff leaking? Pic included

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Frog
    E30 Modder
    • Jun 2010
    • 980

    #1

    Diff leaking? Pic included

    So I looked under my carand found that it was leaking. Is the diff leaking? Or is the the axle?

    There are two lines that are being sprayed. The leaks appear to be coming from where the red arrows are marked. The bolts and where the axle mates with the diff.

    From what I have seen in the past, a leaking diff leaks more toward the diff, and not this far into the axle.

    Please help.
    Attached Files
    Winner winner chicken dinner?

    My Seller Feedback Thread
  • E30Gus
    Mod Crazy
    • Jun 2008
    • 781

    #2
    Those are your axles leaking thick black grease. Have you recently done anything to them or did they just start spewing?

    Comment

    • jlevie
      R3V OG
      • Nov 2006
      • 13530

      #3
      That is grease from the CV joint, not fluid from the differential. New boot kits (use the BMW parts) and fresh grease should fix them.
      The car makes it possible, but the driver makes it happen.
      Jim Levie, Huntsville, AL

      Comment

      • Frog
        E30 Modder
        • Jun 2010
        • 980

        #4
        Just swapped my drum brakes with these disc trailing arm. Bought them used.

        I will do the boot thing, but I hope it isn't too difficult.
        Winner winner chicken dinner?

        My Seller Feedback Thread

        Comment

        • b*saint
          No R3VLimiter
          • May 2006
          • 3794

          #5
          Its easy but is tricky, it helps to have two people sometimes.
          Ma che cazzo state dicendo? :|

          Comment

          • 603Racing
            Mod Crazy
            • Dec 2010
            • 612

            #6
            It looks like the bolts might not be tight enough. Appears to be leaking at the mating surface and from beneath the bolts themselves.

            I have had those bolts loosen up on me before on my e24. Make sure they are tight.
            90 325i DD/Track
            03 Durango 5.9


            Originally posted by e30mpg
            It is recommended to get new gasket but this is R3v and we just copper spray that shit......slap biotch on and tighten to tq.

            Comment

            • 603Racing
              Mod Crazy
              • Dec 2010
              • 612

              #7
              In fact upon further inspection, some of the bolts appear to be backed out more than others. DEFINITELY check this before you continue driving!
              90 325i DD/Track
              03 Durango 5.9


              Originally posted by e30mpg
              It is recommended to get new gasket but this is R3v and we just copper spray that shit......slap biotch on and tighten to tq.

              Comment

              • b*saint
                No R3VLimiter
                • May 2006
                • 3794

                #8
                The bolts don't make a seal tho.

                But yes torque them sums of bitches to 65 ft lbs
                Ma che cazzo state dicendo? :|

                Comment

                • 603Racing
                  Mod Crazy
                  • Dec 2010
                  • 612

                  #9
                  In a round about way, they do make a seal. If there is grease getting in the void where the bolt should be (but it's not because it's backed out) then it will come out at the bolt head. Had this exact same thing happen on my e24 race car, and now it's part of the pre-race checklist.
                  90 325i DD/Track
                  03 Durango 5.9


                  Originally posted by e30mpg
                  It is recommended to get new gasket but this is R3v and we just copper spray that shit......slap biotch on and tighten to tq.

                  Comment

                  • Wishno87
                    R3V OG
                    • Jul 2007
                    • 6025

                    #10
                    Originally posted by 603Racing
                    It looks like the bolts might not be tight enough. Appears to be leaking at the mating surface and from beneath the bolts themselves.

                    I have had those bolts loosen up on me before on my e24. Make sure they are tight.
                    +1 this happened to me too.
                    Your signature picture has been removed since it contained the Photobucket "upgrade your account" image.

                    Comment

                    • e30trooper
                      R3V OG
                      • Mar 2009
                      • 11576

                      #11
                      replace the input shafts stat

                      Comment

                      Working...